User manual SPYKER 85

[. . . ] Attach 2 braces (36) as shown using 3 bolts (24) and 3 nuts (25). Tighten tow bar and bracing supports Insert drive wheel (38) onto axle and insert drive pin (34) and secure with cotter pin (41). Note: For model 80 use cotter pin (41) only. 8. 6. Insert idle wheel (38) onto axle and secure with cotter pin (21) . 9. Attach hitch plates (23) to tow bar using 2 bolts (24) and 2 nuts (25) and tighten securely. Insert clevis pin (26) into hitch assembly and secure with hair pin (27). 3 4 Rate Gate Assembly Final Assembly 10. Attach on/off control cable [37] to control bar with 2 bolts [31] & 2 nuts [29]. Put end cap (30) on lever control bar. 12. Pl ace felt washer (22) over spinner shaft. 13. I 11. Secure on/off control cable to tow bar with cable clamp (32), using 1 bolt (42) and 1 nut (25). [. . . ] BECOME FAMILIAR WITH THE OPERATION OF THE SPREADER BEFORE YOU PUT MATERIAL IN THE HOPPER. Practice walking with the spreader, opening and closing the rate gate at the appropriate times. Travel at a constant speed and operate the spreader lever position. Remember: Open the rate gate after the spreader is in motion at operating speed (about 3 mph. , or at a brisk walking pace). Close the rate gate while spreader is still at operational speed. Dial Setting Information The RATE DIAL has 9 numbers with 10 stops between each number, for accurate control of the spreading rate. It will automatically lock into the set position. LINE UP THE DIAL NUMBER WITH THE DIAL INDICATOR. 7 8 Read Before Using Rotary Agitator Use the rotary agitator only if needed. Free-flowing, lump-free materials will not require the agitator. The rotary agitator is easily installed or removed. Note the clockwise rotation & sweep. Place felt washer around spinner shaft before inserting agitator. OIL BEARINGS AND ALL MOVING PARTS Make certain the spreader is running freely! Read Before Using RECOMMENDATION: When not spreading and the spreader is being pushed some distance, tip the spreader so only the idle wheel is on the ground. Cleaning the Spreader is Part of the Spreading Job. IMMEDIATELY AFTER USE - CLEAN AND OIL THE SPREADER · Method #1 - Wipe spreader thoroughly with an oily cloth. · Method #2 - Wash, rinse, and dry the spreader. (Moisture trapped in bearing areas is slow to go. ) Immediately after drying - oil all bearings and moving parts. Make certain all operations are thorough. Note: Good "Dry Cleaning" is preferable to poor "Wet Cleaning". Now You are Ready to Put Material in the Hopper · Make certain the rate gate is in closed position. · As insurance against spill damage and spill loss, put material in the hopper with the spreader on a walk, driveway, paper, plastic, etc. · The spreader will be easier to use if you only half-fill the hopper. Later on you can fill the hopper if you so choose. · It is virtually impossible to have rust and corrosion on a clean, dry, oiled surface. · Again - just before using - oil all bearings and moving parts. · In storage, ideally the spreader should be hung by the handle. In any case, do not pile weight on the spreader, as excess weight over a period of time can distort the tires. Now You are Ready to Spread · Spread header strips at the ends of the area OPPOSITE the direction of spreading. This will provide a "turn-around" area, an area to realign the spreader for the return spread. [. . . ] Shifts the product placement on the spreading spinner. This in turn balances the spread pattern heavier to right or heavier to left as required. (Note the very fine threads on the Equalizer adjustment stem. ) Viewed from the operators position To spread heavier left - move the ramp out. To spread heavier right - move the ramp in. 1 B 3 Note the relationship of the rate gate opening to the back side of the ramp. 11 12 Granule Size - Dial Setting Guide Dial settings are approximate only. Product Fine Pellets Lbs. [. . . ]