User manual SSI AMERICA NEOCHANGER

[. . . ] Instruction Manual SSI America 43C Rocklyn Ave Lynbrook, NY 11563 Phone 516-887-8885 Fax 516-887-8881 © Multi Technology Equipment LLC ( SSI AMERICA ) v. 1. 3. A All Rights Reserved T able of Contents CHAPTER 1 1 2 3 Installation Preparation (All Vehicles) Anti-Vibration Setup Load/Unload Magazine CHAPTER 2 5 6 7 8-9 Dip-Switch Overview (REQUIRED) Acura Audi Ford (Ford, Lincoln, Mercury) GM (Buick, Cadillac, Chevy, GMC, Oldsmobile, Pontiac, Saturn) 10-11 Chrysler (Jeep, Dodge, Plymouth, Eagle) 13 Honda Toyota Volkswagen 14 15 16 CHAPTER 3 17 18 19 Troubleshooting Warranty/Warnings FCC and Legal Information DESIGN CUSTOMIZATION 1 Chapter Installation Preparation This chapter provides information required for the installation of the Neo Changer, it must be read by all users. Thank you for purchasing the Neo Changer. Since the Neo Changer will works in many different vehicles the following steps must be taken to ensure the changer is set up correctly for the vehicle it is being installed in. Before Installation To prevent damage to your vehicle and the changer take the following precautions. 1. Turn off the ignition and remove the negative (-) battery cable prior to installation. NOTE: If the vehicle is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the battery cable is disconnected, the computer memory may be lost. [. . . ] The screen will change to D1 T1 ( Disc 1, Track 1) Cars using GM-C cable can change disc by turning "P-TYPE" knob + "Seek Type" button to confirm. Other cars press "Prev" or "Next". To change tracks press "Seek <" or "Seek >" When inserting a magazine, Radio display will show Disc # 10, but will be on Disc #1. Press once change disc ( Button # 5) and display will show Disc # 1. Switch to the Neo Changer by pressing the "Aux" or "Source" button. To change discs press "5", "Disc", "1-6 ", or "Side" button To change tracks simply press "Seek <" or "Seek >" Initial use of the changer can take up to two minutes. Please wait while the radio checks the CD magazine. 12 OPERATION FOR XM OPERATION FOR E&C VEHICLE INSTALLATION Chrysler (Chrysler, Jeep, Dodge, Plymouth, Eagle) NOT COMPATIBLE WITH NEW DURANGO, NEW Chrysler 300 and new Magnum 2004 and newer. Make sure the Neo Changer is compatible with your vehicle, Check for "Disc ^" printed on preset button "1". If you see it, it means that your radio can control the Neo Changer. Before connecting any cables you must set the dip switch box to the position listed for your vehicle. If you set the dip-switches after you have connected cables to the box, you must disconnect and reconnect them for the changer to operate. Chrysler's use one of three cables (Old Din, New Din, New 10-pin). Remove the radio to see which cable fits your vehicle, and then refer to settings below. Do not force cables in. SQUARE SHAPE RADIOS: . SETTINGS FOR "CHRYSLER OLD DIN" 1 ON 2 OFF 3 OFF 4 ON 5 OFF 6 OFF 7 ON 8 OFF Use the "Chrysler Old" cable with vehicles 1995-1999/2000. -Connects behind the radio The radios display will not show the proper disc number after disc six. You can use all 10 discs in the magazine, but the readout will be wrong. This is not a technical problem; the car stereo was designed for no more than six discs. *Due to the direct access disc system in the Square shape radios, you will not be able to directly access discs 7-10. To access these discs you will have to go to the last track on disc 6 and let it play until it loads disc #7. ( you can fast forward the track, but you must let it play the last 5 seconds of the track, for it to change to disc # 7 CABLE OVAL SHAPE RADIOS: SETTINGS FOR "CHRYSLER NEW DIN" AND . 1 OFF 2 OFF 3 OFF 4 ON 5 OFF 6 OFF 7 ON 8 OFF "10 PIN" CABLES Use the "Chrysler New" cable with vehicles 1999-2001. Use the "Chrysler New 10-Pin" cable with vehicles 2002-2004. -Connects behind the radio Switch to the Neo Changer by pressing the "CD" or "MODE" button. To change discs press "1" (Disc Down) and "5" or "6" (Disc Up) To change tracks simply press "Seek <" or "Seek >" 13 OPERATION FOR ALL VEHICLE INSTALLATION Honda ­ All Honda except Passport Before connecting any cables you must set the dip switch box to the position listed for your vehicle. [. . . ] We will first work with the 16 pin connector. 16pin Connector: Neo Red to 16pin connectors Orange/Black cable (Pin #9) Neo Blue to 16pin connectors Gray cable (Pin #10) Neo Green to 16pin connectors Light Green/Red cable (Pin #1) Neo Pink to 16pin connectors Violet cable (Pin #2) Neo Yellow to 16pin connectors Light Blue/Pink cable (Pin #7) Neo White to 16pin connectors Tan cable (Pin #8) Neo Brown to 16pin connectors Light Green/Black cable (Pin #6) 24pin Connector: Neo Gray to 24pin connectors Violet/Light Blue cable (Pin #1) Neo Orange to 24pin connectors Black/Light Green cable (Pin #24) *Important Note: Some vehicle production runs do not have a cable plugged into the 16pin pin connector on the back of the headunit. If you are installing in this type of vehicle you can use another Neo cable (For example the Honda cable) and shave the plastic off of the white 22pin connector and remove the pins inside. These pins can then be inserted into the holes on the back of the vehicles stereo. [. . . ]