User manual STAIRVILLE DMX MASTER I

[. . . ] Y Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days. . TABLE OF CONTENTS 1. Lamp EC Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002; EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996, EN61000-4-11: 1994. [. . . ] One of the channels is not working well 1. The stepper motor might be damaged or the cable connected to the PCB is broken. The motor's drive IC on the PCB might be out of condition. The lamp is cutting out intermittently 1. Check the main voltage either too high or too low. Check and if necessary replace the fan on the head. 4B . Warning l l l l l l To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. Never touch bulb with bare fingers as it is very hot after using. Do not open the unit within five minutes after switching off. Do not start on the unit without bulb enclosure or housing are damaged. The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged. Each lighting unit needs to have an address set to receive the data sent by the controller. The address number is between 0-511 (usually 0 & 1 are equal to 1). The end of the DMX MASTER I system should be terminated to reduce signal errors. 3 pin XLR connectors are more popular than 5 pin XLR. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5. 4. Lamp In case of replacement of the lamp or maintenance, do not open the CHANNEL 5 TILT 270° DMX MASTER I CONFIGURATION CHANNEL 1 SHUTTER 255 CHANNEL 2 GOBO 255 Fast CHANNEL 3 COLOR 255 Fast CHANNEL 4 PAN 540° fixture within 15 minutes until the unit cools down after switching off. Lamp : ELC 24V 250W 196 Gobo Shaking 1. Always switch off the main supply and never handle the lamp or luminaries when is hot. If this happens, clean the lamp with denatured Slow Slow alcohol and wipe it with a lint free cloth before installation. Never operate the lamp without appropriate shielding. Make sure the lamp is located in the center for the best spot. 136 Gobo/Color 128 120 112 104 96 88 80 72 64 56 48 40 32 24 16 8 0 92 Color 16 0 GOBOS Gobo Stopped Gobo 14 Gobo 13 Gobo 12 Gobo 11 Gobo 10 Gobo 9 Gobo 8 Gobo 7 Gobo 6 Gobo 5 Gobo 4 Gobo 3 Gobo 2 Gobo 1 Open Blackout 128 121 110 99 88 77 66 55 44 33 22 11 0 Magenta Yellow Blue Light green Pink UV Purple Red Amber Light blue Orange Green White 0° 0° Diagram for Lamp changing 6B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 4. How To Set The Unit 4. 1 Control Panel 5. 2 Easy Controller The easy remote control is used only in master/slave mode. [. . . ] Select the function by ENTER button and the display will blink. Use DOWN and UP button to change the mode. Once the required mode has been selected, press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds. To go back to the functions without any change press the MENU button. [. . . ]