User manual STANDARD HORIZON CPF190I

[. . . ] CP190i - GPS Chart Plotters CPF190i - GPS Chart Plotters/Fish Finder Owner's Manual CP190i CPF190i WARNING!!!Electronic charts displayed by the GPS Chart Plotter are believed to be accurate and reliable, but are not intended to be a substitute for the official charts, which should remain your main reference for all matters related to the execution of safe navigation. For this reason you should always keep the official published and approved nautical charts on board. FCC Compliance Statement This device complies with Part 15 of the FCC limits for Class A digital devices. This equipment generates, uses and can radiate radio frequency energy and, if not installed or used in accordance with the instructions may cause harmful interference with radio communications. [. . . ] After the TD's have been entered, and the user changes to ddd mm. sss (Degrees Minutes and Seconds) the TD's will be converted to Lat / Lon coordinates. To use the TD Coordinate System the user must setup the Chain and Pair information of the TD's. If you do not know this information, refer to paper charts that show the Chain and Pair information. ASF1/2 : Additional Secondary phase Factor (TD Coordinate System) Correction to TD1/2 values which can be inserted by the user to take in account the additional signal propagation delay aver a mixed land/seawater path compared to on allseawater path. Normally the user does not enter a ASF value. However for experienced users this function allows entering of signal delay values to fine adjust the calculated position. The user should enter delay values to fine adjust the position calculated. : Alternate Solution (TD Coordinate System) Parameter selected by the user that is applied in the conversion of geographical coordinates Lat/Lon to TD values. To be used if the position displayed is roughly not correct. Alter 13. 2 COMPASS The GPS Chart Plotter computes compass direction from the constellation of GPS Satellites. For the GPS Chart Plotter to compute direction the vessel must be moving through the water unless connected to an optional Flux Gate Compass sensor. The Compass menu allows the GPS Chart Plotter to customize the following selections: : Selects between True and Magnetic. When Magnetic bearings is enabled, the GPS Chart Plotter applies the selected MagneticVariation (Auto or Manual, see next paragraph) to compute Magnetic bearing. Variation : Allows the user to select Auto or Manual. When Auto mode is selected the GPS Chart Plotter computes the ofset by the curent GPS fixed location. Manual mode allows the user to enter in a magnetic variation that is applied in the True conversion. Calibration : This function allows a user to enter in the offset for areas that the vessel may cruise instead of entering in a manual offset for one location. This offset is useful for cruising vessels or vessels that travel internationally often. Bearings Figure 13. 2 - Compass Table 13. 3 ALARMS The Alarms menu is used to select and setup audible and visual Alarms. Available alarms are Arrival, XTE, Depth, Anchor and Grounding Alarm. CP190i and CPF190i Page 107 : Alerts when the vessel is approaching single destination point or when arriving at a leg in a Route. XTE Alarm : Alerts when the vessel is deviating from a defined course. Depth Alarm : Alerts when the received depth Value is lower than the selected value. Anchor Alarm : Alerts when the ships moves off a selected locations by a selected distance. Audible Alarm : Enables or disables the alarm beep. [. . . ] 56 Zoom Full page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 ZOOM IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 ZOOM OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Zoom Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]