User manual STANDARD HORIZON CPF390I

[. . . ] CP390i - GPS Chart Plotters CPF390i - GPS Chart Plotters/Fish Finder Owner's Manual WAAS 3D CP390i CPF390i WARNING!!!Electronic charts displayed by the GPS Chart Plotter are believed to be accurate and reliable, but are not intended to be a substitute for the official charts, which should remain your main reference for all matters related to the execution of safe navigation. For this reason you should always keep the official published and approved nautical charts on board. FCC Compliance Statement This device complies with Part 15 of the FCC limits for Class A digital devices. This equipment generates, uses and can radiate radio frequency energy and, if not installed or used in accordance with the instructions may cause harmful interference with radio communications. [. . . ] Compatible VHF Marine Radios with Digital Selective Calling are able to be interfaced with the GPS Chart Plotter which feeds GPS data to the VHF and listens for DSC calls from the VHF. By connecting a few wires between the compatible DSC VHF radios and the GPS Chart Plotter it will receive: 1. a vessel that has transmitted a DSC Distress call CP390i and CPF390i Page 107 2. a vessel that has transmitted a DSC Position Send Call 3. The position of a vessel that transmitted a DSC Position Request Call 12. 9. 0 Interfacing To take advantage of these functions the GPS chart plotter must be interfaced (wired) to a STANDARD HORIZON or compatible DSC VHF. For additional information refer to Par. 2. 4 Connections. 12. 9. 1 Distress Call STANDARD HORIZON GPS chart plotters are able to display the location of a vessel in distress when interfaced to a compatible DSC VHF with NMEA 0183 output and the radio receives a DSC Distress Call. STANDARD HORIZON GPS chart plotter also log DSC Distress calls to review at a later date. Press [MENU] and move the ShuttlePoint knob to highlight USER POINTS and press [ENT]. Move the ShuttlePoint knob to highlight DSC Log and press [ENT]. 03-03-01 08:31 PM 03-04-01 00:11 PM 03-04-01 09:31 PM Disabled and adrift Undesignated distress Collision PATTY 0080457645 ROY 0023244524 BOBI 0056477743 33°30. 505 N 08:31 PM 118°18. 529 W 33°34. 167 N 00:11 PM 118°21. 864 W 33°31. 211 N 09:31 PM 118°29. 151 W NO YES NO Figure 12. 9. 1 - DSC Log - Distress Call 12. 9. 2 Position Request STANDARD HORIZON GPS chart plotters are able to display the location of a vessel when connected DSC VHF radio and when a Position Request or Report call is received. STANDARD HORIZON GPS also log DSC Distress calls to review at a later date. Press [MENU] and move the ShuttlePoint knob to highlight USER POINTS and press [ENT]. Move the ShuttlePoint knob to highlight DSC Log and press [ENT]. Move the ShuttlePoint knob to the right to select POSITION REQUEST and press [ENT]. Page 108 CP390i and CPF390i 03-03-01 08:31 PM 03-04-01 00:11 PM 03-04-01 09:31 PM 33°30. 505 118°18. 529 33°34. 167 118°21. 864 33°31. 211 118°29. 151 N W N W N W PINKO 0080457645 ROY 0023244524 BOBI 0056477743 NO YES NO Figure 12. 9. 2 - DSC Log - Position Request CP390i and CPF390i Page 109 Page 110 CP390i and CPF390i 13. ADVANCED SETTINGS The Advanced Setup menu allows customization of many GPS functions, Alarms and NMEA interfacing. Press [MENU], move the ShuttlePoint knob to highlight SETUP MENU and press [ENT]. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move the ShuttlePoint knob to the right. While in this menu you will see many selections which are described in the next sections. 13. 0 INPUT/OUTPUT (NMEA, AIS, RADAR) 13. 0. 0 Input The CP390i has 4 Inputs and 5 Outputs connections. The CPF390i has 3 Inputs and 3 Outputs connections. These ports may be set up to receive and output the following. · NMEA-0183 - NMEA devices* set to 4800 Baud (default setting) · Fish Finder: Only for CP390i: FF525 50/200kHz BLACK BOX FISH FINDER - refer to Fish Finder Owner's Manual · C-Com - C-Weather refer to Section 15 · Radar - SI-TEX optional Radar refer to Radar Owner's Manual · AIS38400 - AIS Receiver, refer to Section 14 · MOBILARM - Mobil-arm receiver, refer to Section 16 · Disabled - allow the port to be disabled. NOTE* RS232 not opto-isolated electrical interface NOTE When a Port is configured, both the Input and Output have the same setting. Port1 is set to Radar, both the Input and Output wires are set to SI-TEX proprietary Radar sentences. [. . . ] 133 ZOOM IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 ZOOM OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Zoom Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 Zoom Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]