User manual STANDARD HORIZON GARMIN GPSMAP 192C TO MATRIX GX2100 WIRING

[. . . ] This limitation is due to the current technology of the LCD displays. Avoid overheating which may cause loss of contrast and, in extreme cases, a darkening of the screen. Problems which occur from overheating are reversible when temperature decreases. Achtung! Ultraviolette Strahlen können die Lebensdauer vom Flüssigkristalldisplay verkürzen. Die derzeitige LCD-Technologie bedingt diese verkürzte Lebensdauer. [. . . ] Move the ShuttlePoint knob up/down to place the selector on the desired item; move the ShuttlePoint knob to the right or press 'ENTER' to set the selected item; move the ShuttlePoint knob to the left or press 'CLEAR' to close the pop-up window (see also Section 3. 1. 1). (NMEA) Data page 'MENU' + "NMEA DISPLAY" + 'ENTER' + "DATA" + 'ENTER' or press any soft key + 'DATA' (if it is present) Shows the stream of NMEA-0183 sentences read from the NMEA port. Pressing 'ENTER' stops/starts alternatively the page update. Figure 8a - NMEA Data Page Data Window It is possible to customize the data window layout among None (only charts), General (text area on the right side of the screen), 1line small, 1 line large, 2 lines small. The default setting is General. 'MENU' + "GENERAL SETUP" + 'ENTER' + "DATA WINDOW" + 'ENTER' Date (Simulation) Sets the date of the simulated fix. Inserts date using the ShuttlePoint knob. 'MENU' + "ADVANCED SETUP" + 'ENTER' + "SIMULATION" + 'ENTER' + "DATE" + 'ENTER' Date Format Sets the preferred date between MM-D-YY and DD-MM-YY. The default setting is MM-DD-YY. 'MENU' + "GENERAL SETUP" + 'ENTER' + "DATE FORMAT" + 'ENTER' Datum The Latitude and Longitude lines printed on any map are based on certain models of the shape of the earth: these models are called Datum or Coordinate Systems. There are many different Datum in use, each one gives different Lat/Lon positions for an identical point on the surface of the earth (see Part A of " Handbook"). Dedicated key A key with permanently defined function. These keys are labelled on the front panel of the chartplotter. Default Indicates a value or a setting which is used if the user has not defined a particular value. You can modify this value using the menu settings. GPS Chart 160/170C Page 67 Delete (File) Deletes file from User C-CARD. 'MENU' + "USER C-CARD" + 'ENTER' + "DELETE" + 'ENTER' or press any soft key + 'C-CARD' (if it is present) + "DELETE" + 'ENTER' Delete (Route) To delete the selected Route. 'MENU' + "ROUTE" + 'ENTER' + "DELETE" + 'ENTER' + "YES" + 'ENTER' Delete (Track) To clear the stored Track. 'MENU' + "TRACK" + 'ENTER' + "DELETE" + 'ENTER' + "YES" + 'ENTER' Depth (Unit) Sets the depth units among Ft = Feet, FM = Fathoms and Mt = Meters. The default value of the field is Yes (object shown on the map). Position Request: Shows Position Request LOG Page. When Position Request LOG Page is active this message changes to Distress Call LOG Page. (DSC) Directory page Shows the Directory when a DSC Distress Call or Position Request is received to look up the name of the vessel and display it on the screen. 'MENU' + "DSC" + 'ENTER' + "DIRECTORY" + 'ENTER' or press any soft key + 'DIR' (if it is present) DSC (menu) Selects the (DSC) LOG and (DSC) Directory pages. 'MENU' + "DSC" + 'ENTER' Distance (Track) When the tracking function is On and the type of Track storing is Distance, you can store a fix when the distance from its last stored position is greater than a defined distance. Choose in the range 0. 01, 0. 05, 0. 1, 0. 5, 1. 0, 2. 0, 5. 0, 10. 0 Nm (the distance unit is selected by the user). The default setting is 0. 01 Nm. 'MENU' + "TRACK" + 'ENTER' + "DISTANCE" + 'ENTER' Distance (Unit) Sets the distance unit among Nm = nautical miles, Sm = status miles e Km = kilometers. The default setting is Nm. 'MENU' + "GENERAL SETUP" + 'ENTER' + "UNITS OF MEASURE" + 'ENTER' + "DISTANCE" + 'ENTER' Distress Call Distress Call and Position Request are functions performed by an external device (VHF DSC radio) connected to NMEA Input Port. The chartplotter allows seeing and recording up to 20 Distress Calls and Position Requests sent by the VHF radio for a total of 40. When a Distress Call or a Position Request is received the chartplotter will automatically mark the position on the chart and add the information on the proper Log. A pop-up screen advise the user that a Distress Call or Position Request call has been received. Within the pop-up screen it asks the user if he would like to view the call on the chart ("VIEW ON CHART") or exit the pop-up screen. [. . . ] 51, 80 Track memorizing type . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Track storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51, 80 Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Tracks & Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]