User manual STANDART HORIZON CP160

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual STANDART HORIZON CP160. We hope that this STANDART HORIZON CP160 user guide will be useful to you.

Lastmanuals help download the user guide STANDART HORIZON CP160.


Mode d'emploi STANDART HORIZON CP160
Download
Manual abstract: user guide STANDART HORIZON CP160

Detailed instructions for use are in the User's Guide.

[. . . ] Place bracket (W) 50 mm from the ceiling and position this on the vertical of your hood, with the aid of the notches on the centre of the bracket (Fig. 6); using a pen, mark the 2 holes on the wall and then make the holes and fit the screw anchors provided and proceed to secure the bracket using the 2 screws (provided). Exhaust hoods: connect the disposal duct to the air evacuation pipe of the hood; use a flexible pipe and lock it to the air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). Make all power connections to the hood by means of the power cable. [. . . ] If pressed for 2" the motor is turned off. Button D: activates the motor (calling the last speed used) and increases the speed until reaching maximum. Button E: FILTER ALARM/TIMER RESET: when pressing the key during display of the filter alarm (motor off) it resets the hour counter. When pressing the key when the motor is running, the TIMER is activated and the hood will automatically be switched off after 5 minutes. L1) The 4 green LEDs indicate the running speed. L2) When the LED is red (motor off) it indicates the FILTER ALARM. When the LED is green (flashing) it indicates that the TIMER has been activated with the key E. FILTER ALARM: After 30h of operation, the LED L2 turns RED. It indicates that the grease filters need to be cleaned. After 120h of operation, the LED L2 turns RED and flashes; It indicates that the grease filters need to be cleaned and the charcoal filters replaced. After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter (RESET) by pressing the key E during display of the filter alarm. 13” (“Filter Alarm”). If the model purchased has the controls shown in Figure 11/12, the charcoal filters must be replaced according to use: on the average once every 6 months. If the model purchased has the controls shown in Figure14, the charcoal filters must be replaced each time the light button (Fig. Lighting: - To gain access to the bulbs, remove the grease filters as described above and remove the bulbs. Replace only with CANDLE HALOGEN LAMP - Ø 35mm, E14–220-240 Vac, 28W or INCANDESCENT LAMP-E14–220-240 Vac, 40W - If the halogen lamps shown in Fig. 16 need changing, slacken the ring nut in an anticlockwise direction and remove the bulb itself. CAUTION: Do not handle glass bulb with bare hands. - To change the halogen lamps shown in Fig. 17 open the cover levering from the proper slots. CAUTION: Do not handle glass bulb with bare hands. The motor used in this hood features a safety device (thermal cutout) that responds to temperature changes For accidental reasons or due to installation faults, this device could engage and automatically shut off the motor, thereby preventing serious damage to the equipment. [. . . ] In fact the intake hood, disposing of air, could create a vacuum in the room. The vacuum should not exceed heat source from being intaken again. It is therefore advisable to ensure the room contains air taps able Check the data label inside the appliance; if the symbol ( ) is printed, read the following: this appliance has such technical particulars that it belongs to class II insulation, therefore it must not be earthed. Check the data label inside the appliance; if the symbol ( ) is NOT printed, read the following: ATTENTION: This appliance must be earthed. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE STANDART HORIZON CP160

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual STANDART HORIZON CP160 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag