User manual STANTON STR8-20 TURNTABLE

[. . . ] FULL MANUAL BELT DRIVE TURNTABLE STR8-20 WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. NAME OF PARTS 1) 2) 3) 4) 5) 6) 7) Strobe Dots Slip Mat Center Spindle Power Switch Start/Stop Button 33 Button 45 Button 8) 9) 10) 11) 12) 13) Headshell Pitch Control Slider Tonearm Arm Rest Counterweight Position For Preparing Cartridge BEFORE USE *Check following parts included in the package with the main unit: 1) Turntable platter 2) Slip mat 3) 45-rpm adaptor 4) Counterweight 5) Headshell 6) Operating instructions 7) RCA Cables with ground wire 8) Cartridge *Notes: 1) Do not connect the AC power plug before assembly has been completed. 2) Before you turn on the power, verify the voltage setting is correct for your country. 3) Read this manual carefully before using the unit and be sure to store the manual in a safe place for future reference. ASSEMBLY 1. [. . . ] (e) Hold the counterweight stationary with one hand and rotate only the stylus-pressure ring to bring the number "0" of the ring into alignment with the center line on the tonearm rear shaft. (f) Rotate the counterweight clockwise until the scale shows the value corresponding to the pressure of the used stylus. The average stylus pressure of the cartridge body is 2g. If you use a non-Stanton cartridge, please follow that manufacturer's instructions. Install the dust cover to the main unit. PLACEMENT · Do not place the unit in a location where it will be exposed to direct sunlight or near a heating appliance. · Do not place the unit in a location where there is high humidity or a lot of dust. · Cartridge may pick up slight sound pressures or vibrations from the speakers coming along the floor or through the air resulting in feedback. Find a location which is very stable and vibration free. · The legs have functions for adjusting the height of the unit itself. Adjust the legs to stabilize the main body horizontally. CONNECTIONS 1. Connect the power cord to the auxiliary power outlet on the rear panel of your amplifier or receiver or to a household AC outlet. Connect the unit output terminals to the PHONO jack of your amplifier or receiver. Output terminals Amplifier(Receiver) L (White) >> L Channel R (Red) >> R Channel GND (Spade) >> GND NOTE: Be sure to connect the ground terminal firmly to the amplifier or receiver. If this connection is not made or is loose, a power source "HUM" will result. OPERATION 1. Rotate the power dial clockwise to turn on the power, the speed indicator and the strobeilluminator will light up. Place a record on the slip mat, when playing a 45rpm record with a large center hole, place the 45rpm adaptor on the center spindle. [. . . ] · From time to time, the dust cover and turntable cabinet should be wiped with a soft and dry cloth. · Any volatile materials such as alcohol, thinner, benzine, etc. , may remove the paint or damage the lustre, please avoid. SPECIFICATIONS *General Power supply. . . . . . . . . . . . . . . . . . . . AC 115/230V~, 50/60Hz Power consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Watts Dimension (W*D*H). . . . . . . . . . . . . . . . . . 450 x 350 x 140 mm Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. 5Kgs For improvement purposes, specifications and design may be changed without notice. 502-STR820-1304 [. . . ]