User manual STRONG SRT 5203

[. . . ] The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of not insulated dangerous voltage within the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operation and servicing instructions in the literature accompanying the appliance. Read the following instructions carefully TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT The apparatus shall not be exposed to dripping or splashing, and that no objects filled with liquids, such as vases, shall be place on the apparatus. [. . . ] CONNECTION: Connect all components before plugging any power cords into the wall outlet. Always turn off the receiver, TV and other components before you connect or disconnect any cables. SERVICING: Do not attempt to service this product yourself. Any attempt to do so will make the warranty invalid. Refer all servicing to a qualified service agent. LIGHTNING: If the receiver is installed in an area subject to intense lightning activity, protection devices for the receiver mains connector and modem telephone line are essential. The individual manufacturer's instruction for safeguarding other equipment, such as TV set, Hi-Fi, etc. , connected to the receiver must also be followed during lightning storms. The grounding system must comply with SABS 061. NOTE: Dispose the used batteries at designated place for environment protection 5 English PART 2 · English 2. 0 INTRODUCTION 2. 1 Front Panel 1. Display I In ON mode channel number is shown 2. 2 Rear Panel 1. ANT IN To connect your terrestrial antenna 2. n By using "Quick Installation" the channel search will start. n By using "Advanced Installation", "Language select", "TV/VCR settings", "Time settings" and "Antenna settings" be defined manually. n Choose "Language select" by using the pqtu buttons. Here you can set up; Menu language, 1st Audio lang and 2nd audio lang and 1st text lang and 2nd text lang n Choose "TV/VCR settings" by using the pqtu buttons. Here you can set up; HDMI output, TV Screen Format, Picture Format and HDCP Always Enabled n Choose "Time settings" by using the pqtu buttons. Here you can set up; Country, Time zone selection, preferred Time zone and if daylight savings time should be activated. n Choose "Antenna settings" by using the pqtu buttons. Here you can set up antenna supply n When you have made the changes you want, press BLUE "Save&Next" to go to the next step. 4. 3 Channel Search In this menu you can select a channel with signal to adjust your antenna for max signal en reception n Select "MUX" to choose a channel to test signal strength. Enter the channel number with the numeric keys on the remote control. n Select "Frequency" to manually enter a frequency to test signal strength. Enter the frequency using the numeric keys on the remote control. [. . . ] Press GREEN button to get detailed reception information. 13 English PART 2 · English 6. 10 Switching between DTV and Radio mode You can switch between Digital TV mode and Radio mode by pressing "TV/RAD" button on your remote. 7. 0 SPECIFICATION Demodulator Modulation: Frequency range : Channel bandwidth: MPEG Video Decoder Standards: Formats: Aspect ratio: Video Scaling: OSD Colours: Resolution: Overlay: MPEG Audio Decoder DTS Licence number: Standard : DVB-T COFDM 174 ­ 234 MHz (VHF III) 470 ­ 862 MHz (UHF IV/V) 7/8 MHz switchable bandwidth ISO13818-2 (MPEG-2) ­ MP@ML, MP@HL ISO14496-10 MPEG-4 AVC MP@L3, HP@L4 576i25 (SD), 576p50, 720p50 (HD), 1080i25 (HD) 4 :3, 16 :9, Pan & Scan, Letter Box Variable 16/256 colours 2 ­ 16 bits per pixel MPEG stills/live image insertion ISO 11172-3 / ISO 13818-3 (MPEG) ISO14496-3 MPEG-4 AAC ­ LC/HE Dolby Digital (AC3) Decompression MPEG layers 1, 2 (Mono, Dual Channel, Joint Stereo, Stereo) HE-AAC (profile v1) level 4 decoding S/PDIF and HDMI audio output formats: PCM (decompressed stereo) Compressed Dolby Digital 5. 1 pass-through DTS with transcoded multichannel HE-AAC System resources Processor: RAM (system): ST7101 64 MBytes Loader Full code software download mechanism Authentication of downloaded material 14 PART 2 · English Front panel 3 digits 7 segments red display. 3 LEDs with backlighted symbols 3 buttons Smartcard slot Software & Features Access control: Setup menu: EPG: Languages: CONAX CAS7 with chipset pairing Automatic channel installation, diagnosis, decoder configuration, parental control 7 days of EPG, if available from distributor multilingual OSD, audio and signaling supported Teletext processing EN 300 472 teletext re-insertion in the composite video signal EN 300 472 & EN 300 743 teletext and subtitling decoding Interfaces Mains input connector: ANT input: TO TV: 1 Scart: Analogue Audio: Digital Audio: Digital Video/Audio: Smartcard reader: General data Mains voltage: Power consumption: Typical consumption: Power consumption in standby: Operating temperature: Product dimensions: Weight: DTS License number: Detachable lead IEC-type, female IEC-type, male (loop-through) TV with RGB 2 RCA Stereo audio outputs (left and right) S/PDIF audio electrical output HDMI 1. 2A with HDCP copy protection 1 slot, ISO 7816 1, 2 & 3 96 ­ 264 V 48/62 Hz max 10 W 8. 5 W in SD / 9. 5 W in HD max 0. 5 W +10 ~ +40 °C 280 x 200 x 35 mm 1. 2 kg C103471 Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. [. . . ]