User manual STRONG SRT 5501 MHP

[. . . ] It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards. Your warranty will be void if the receiver has been opened n When the receiver is not used for a long period of time, you should unplug the power cord from the wall socket n Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you may clean your receiver with a soft lint-free cloth slightly made damp with a mild soap solution, only after disconnecting from the mains voltage supply. Make sure no foreign objects fall through the ventilation slots because this could cause fire or an electric shock n Do not place any objects on top of the receiver because this might prevent proper cooling of the components inside n Safety Precautions Do not open the receiver cover, as you will be exposed to a shock hazard. [. . . ] If mode is Free+Scrambled then all channels from selected satellite will be added to the channel list. Press the YELLOW Key to set the Blind Scan to ON or OFF. Blind scan function is useful to scan new added satellite, but scan may take long time. Press the BLUE Key to set the scan type to NIT OFF or NIT ON while Blind Scan is set to OFF and to Quick Search or Detail Search while Blind Scan is set to ON. When the set-up is completed, press the RED key to start the scan, shown as below. 5. 2. 3 Manual Scan In this menu, you can scan single transponder, add a new transponder, edit the transponder or delete the transponder. You can switch between satellites with the RED button, Scan transponder: Use UP/DOWN buttons to select the transponder. Add Transponder: In this menu, you can add a new transponder to the system. Press the GREEN button, the Add Transponder sub-menu will appear. Frequency: input the frequency of the new transponder. Symbol Rate: input the symbol rate of the new transponder. Polarity: Select the Polarity of the new transponder. If the menu lock is on, then for some operations such as search program and set factory default, you need to enter your PIN. 5. 3. 3. 3 Parental Setting Set some channels to lock status. If a channel is locked, the user has to enter the parental PIN code correctly before watching the locked channel. Use the UP/DOWN keys to select the channel you want to lock. Press the OK button to lock the channel. 5. 3. 3. 4 Change PIN Modifying the PIN, you must enter the 4 digits PIN and confirm it again; the system PIN will be changed to the new PIN. 5. 3. 4 System info The system information displays information about your receiver such as software and User Interface version. Compare version of the software given on this menu with version available in the internet in order to know if you have latest version of software. 5. 3. 5 System Update In this menu, you can select between "STB to STB" and "OAD" 5. 3. 5. 1 STB to STB spftware transfer 1. First power off both STBs, connect them with cross RS-232. Then power on master STB (master is STB from which you will copy software) and keep slave STB off. Navigate in the menu of master STB and select "System Update ­ STB to STB". When the status displays "detecting slave STB", power on slave STB, after the master STB detects the slave, the master starts transmission and burns. While transmitting and burning, it is very important to avoid other operations such as power off because this may cause destruction of the data in the FLASH memory and the receiver will need to be repaired. When update is complete, first power off both STBs, then disconnect the RS-232 line. 5. 3. 5. 2 Over Air Download (OAD) Select this option in order to update your receiver with the latest software version. [. . . ] Check the antenna cable, replace the cable, or connect the cable to the receiver tightly. 17 English move menu focus to selection of group. Use LEFT/RIGHT buttons to select group of your choice. Select group "NO FAV" and press OK if you wish to exit from favourite channel list mode. PART 1 · English Symptom Cause Incorrect values of some tuner parameters Wrong direction of the dish Remedy Set the values of the tuner parameters correctly in the installation menu. Check the signal strength with a spectrum analyzer and adjust your dish correctly. [. . . ]