User manual STRONG SRT 6300W - SRT 630WS

[. . . ] Digital Wireless Satellite Receiver with Digital Recorder SRT 6300 W Digital Wireless Satellite Receiver SRT 630 WS User Manual SRT 6300 W SRT 630 WS Picture similar TABLE OF CONTENTS 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Introduction 1. 5 Features & Accessories 2. 0 YOUR RECEIVER 2. 1 Master SRT 6300 W Front Panel 2. 2 Master SRT 6300 W Rear Panel 2. 3 Slave SRT 630 WS Front Panel 2. 4 Slave SRT 630 WS Rear Panel 2. 5 Remote Control 3. 0 INSTALLATION 3. 1 Master SRT 6300 W 3. 2 Slave 3. 3 Wireless Network Configuration 4. 0 QUICK START 5. 0 MENU OPERATION 5. 1 Main Menu 5. 2 Channel Organizer 5. 3 Favourite Organizer 5. 4 Timer Setup 5. 5 Installation 5. 6 Media Base 5. 7 Media Base Management 5. 8 Media Base Transfer 5. 9 Common Interface (Master Only) 6. 0 FUNCTION GUIDE 6. 1 Channel List 6. 2 Information Box 6. 3 EPG (Electronic Programme Guide) 6. 4 Subtitle 6. 5 Teletext 6. 6 Sound Track 6. 7 Time Shifting 6. 8 Recording 3 3 4 4 4 5 6 6 6 7 8 8 10 11 13 15 17 17 17 18 19 20 21 28 29 29 30 31 31 31 32 32 32 32 33 33 1 6. 9 Play Files 6. 10 Stop 6. 11 Pause 6. 12 Slow Motion Playback 6. 13 Fast Forwarding and Rewinding 6. 14 Bookmark 6. 15 Repeat 6. 16 Picture In Picture (PIP, Master Only) 6. 17 Keyboard 7. 0 TURN OFF SYSTEM 7. 1 Master 7. 2 Slave 8. 0 SOFTWARE UPDATE 9. 0 SPECIFICATIONS 9. 1 Master 9. 2 Slave 10. 0 TROUBLESHOOTING 34 34 34 35 35 35 36 36 37 38 38 38 38 39 39 40 42 2 1. 0 INTRODUCTION 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: n In a closed or poorly ventilated cabinet; directly on top of or under any another equipment; on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: n To direct sunlight or near any other equipment that generates heat; to rain or intense moisture; to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc n Do not use a damaged power cord. It may cause a fire or an electrical shock. Do not touch a power cord with wet hands. It may cause an electric shock n Never open the cover. [. . . ] Connection Type The default value is Twin LNB, you can change it to Separated Note: If you change the Connection Type all channels will be deleted. Tuner Select a tuner for channel searching from the selected satellite. The LNB Frequency: 5150, 11300, 11450, 9750/10600, 9750/10650, 9750/10700, 9750/10750 can be selected with [VOL-/VOL+] buttons. You can enter LNB frequency also by using Numeric keys on the remote control The most used setting are the universal LNB settings 9750/10600. LNB Power Select LNB power ON to output the LNB voltage. Switch 22 kHz If you are using a 22 kHz tone to select different satellite dishes or bandwith to Master, make the 22 kHz tone switch enable or disable to select dish or LNB. Note: If the LNB Frequency is set to Universal LNB (9750/10600 or 9750/ 10650, 9750/10700, 9750/10750), it is impossible to set 22 kHz because it is a default setting in this application. 23 DiSEqC Version You can choose Tone Burst, DiSEqC 1. 0, DiSEqC 1. 1 or Disable. Tone Burst allows two satellite dishes to be connected to the Master at the same time. DiSEqC 1. 0 and 1. 1 allow multiple antennas to be connected to the Master at the same time. If you are using five or more fixed antennas or LNBs, then it is recommended using a DiSEqC 1. 1 switch. DiSEqC Port Choose to which DiSEqC Input your selected dish is connected to. Tone Burst has two options: Tone A for port 1 and Tone B for port 2. Transponder To test your settings you can choose a transponder with a strong signal. If your settings are correct then the level and quality banners should show a signal. Dish Type Choose the Dish Type you use Fixed, DiSEqC 1. 2, USALS. If you choose DiSEqC 1. 2, then press the [OK] button to enter DiSEqC 1. 2 Setup menu. If you choose USALS, then press the [OK] button to enter USALS Setup menu. Channel Setup To go to Channel setup menu directly from LNB setting menu press the [OK] button. 5. 5. 4 Channel Setup (Master Only) Satellite Press [OK] button to display the Satellite List. Select one of the pre-programmed satellites that correspond to the satellite dish. If the desired satellite name is not in the list, select "Other". Tuner Select a tuner for channel searching. The Auto mode enables you to search using the information the Master has. [. . . ] After the update has finished, the Master and Slave(s) will reboot automatically. 38 9. 0 SPECIFICATIONS 9. 1 Master Double Tuners Input / Loop through Connector Frequency Range Signal Level input LNB Power & Polarization DVB-S 75 Ohm, IEC 169-24 950 ~ 2150 MHz -10 ~ -80 dBm @ 27. 5 MS/s Vertical: +13 V DC Horizontal: +18 V DC Current: Max 500 mA Overload protection 22 kHz +/- 2 kHz, 0. 6 Vpp +/- 0. 2 V V1. 0/1. 1/1. 2/1. 3(compatible) QPSK 1 ~ 45 Mbps, SCPC/MCPC 22 kHz Tone DiSEqC Demodulation Input Symbol Rate MPEG Transport Stream, A/V Decoding Transport Stream Profile Level Aspect Ratio Video Resolution Audio Decoding Main System Main Processor Memory MPEG-2 TS Specification (ISO/IEC 13818) MPEG-2 MP@ML 4:3 / 16:9 720 x 576 (PAL), 720 x 480 (NTSC) MPEG 1 Layer 1, 2, 3 HDD Front Panel & RCU 7 KEYs VFD 2 LEDs RCU Conditional Access Interface PCMCIA ST I5100 Flash-ROM: RAM: EEPROM: 160 GB 8 MBytes 64 MBytes 1 kbits CH-/+, VOL-/+, MENU, OK, STANDBY Time, Service name and other info STANDBY & POWER ON 47 keys 2 slots DVB common interface Standard 39 A/V & Data In/Out TV-SCART VCR-SCART S-Video RCA A/V S/PDIF RS-232C USB RF-Modulator RF-Connector Output Service TV standard Power Supply Input Voltage Type Power Consumption Protection Physical Specification Size (W X H X D) Weight (Net) Video CVBS/RGB/Y/C Output Audio L/R Output Video CVBS/RGB Output Audio L/R Output Video CVBS/RGB Input Bypass Audio L/R Input Bypass Video S-VIDEO Output Video CVBS Output Audio L/R Output Digital Audio or Dolby AC-3 bitstream Output 9 pin CD-SUB type Transfer rate 115. 2 kbps USB 2. 0 Device 75 Ohm, IEC 169-2, Female / Male CH 21 ~ 69 (PAL/NTSC) PAL G/I/K, NTSC selected by Menu 90 ~ 240 V AC 30 W AC Fuse 340 x 265 x 60 mm 3. 35 kg 9. 2 Slave MPEG Transport Stream, A/V Decoding Profile Level Aspect Ratio Video Resolution Audio Decoding Main System Main Processor Memory MPEG-2 MP@ML 4:3 / 16:9 720 x 576 (PAL), 720 x 480 (NTSC) MPEG 1 Layer 1, 2, 3 ST I5100 Flash-ROM: RAM: EEPROM: 8 MBytes 32 MBytes 1 kbits 40 Front Panel & RCU 7 KEYs 4-digital 7-segment LEDs 3 LEDs RCU A/V & Data In/Out TV-SCART VCR-SCART CH-/+, VOL-/+, MENU, OK, STANDBY Time, Service name and other info Link, Record, Power on/Standby 47 keys S-Video RCA A/V S/PDIF USB Power Supply Input Voltage Type Power Consumption Protection Physical Specification ITEM Specification Size (W X H X D) Weight (Net) Note: Video CVBS/RGB/Y/C Output Audio L/R Output Video CVBS/RGB Output Audio L/R Output Video CVBS/RGB Input Bypass Audio L/R Input Bypass Video S-VIDEO Output Video CVBS Output Audio L/R Ouptut Digital Audio or Dolby AC-3 Bitstream Output USB 2. 0 Device 10. 4 ~ 12. 6 V DC 11 W DC Fuse 165 x 60 x 160 mm 1. 06 kg Specification and functions may be changed for improvement without notice in advance. 41 10. 0 TROUBLESHOOTING Occasionally the receiver may hang-up. In that case it is recommended to reset the receiver by disconnecting it from the main power. Wait 30 seconds and connect to main power again, then see if the unit is working as expected. [. . . ]