User manual STRONG SRT 6500 CI

[. . . ] Digital Satellite Receiver with Cryptoworks Embedded and Common Interface SRT 6500 CI User Manual PART 1 · English TABLE OF CONTENTS English 1 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features and Accessories 2 2 2 2 3 4 4 4 5 7 7 7 8 8 9 10 10 10 16 21 25 26 2. 0 YOUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control 3. 0 CONNECTING THE RECEIVER 3. 1 To a TV set, using TV SCART connection. 3. 2 To a HiFi system and a TV set, using both A/V connections 3. 3 To a VCR and a TV set, using both SCART connections 3. 4 To VCR and a TV set, using build-in UHF modulator 4. 0 5. 0 STARTING UP FOR THE FIRST TIME SETUP AND OPERATION 5. 1 Before Setup 5. 2 Setup Menu 5. 3 Main Menu Settings 5. 4 General Viewing Information A1 A. 2 PROBLEM SOLVING SPECIFICATIONS PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: n In a closed or poorly ventilated cabinet; directly on top of or under any another equipment; on a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: n To direct sunlight or near any other equipment that generates heat; to rain or intense moisture; to intense vibration and to any not use a damaged power cord. It may cause a fire or an electrical shock. [. . . ] 5. 2. 3. 4 How to correct/edit parameters of the transponder: n set "Tune method" to "TP" or "TP+NIT" focus to "Transponder" and choose transponder you want to modify focus to "Frequency" and enter value in MHz focus to "Symbol rate" and enter value in kSPS focus to "Polarity" and select value focus to "FEC" and select value or set "Auto" focus to "Function" select "Change" and press OK. Message "Saving data. . . " will be shown on screen. Modified data are n move n move n move n move n move n move stored in the memory. n Press EXIT to go back to the previous mode. 5. 2. 4 Setup Lock/PIN Press OK on `Setup Lock/PIN' in the Setup Menu. Set the Menu Lock, Change the PIN, enter the New PIN and confirm the Confirm PIN. n Use n Use CH p/q to move up and down the list. Menu Lock: On/Off Change PIN: Press OK if you want to change. New PIN: Enter your new 4-digit code Confirm PIN: Confirm your new 4-digit code * Note: The default PIN is `1234' n Press EXIT to go back to the previous mode. 5. 2. 5 Time Setting Press OK on `Time Setting' in the Setup Menu. Set the Local Time, Sleep Time, Timer Status and Program the Timer. n Use n Use CH p/q to move up and down the list. Vol t/u to change the setting. 14 PART 1 · English Local Time: if you want to correct time and date then enter in format dd/ mm/yyyy - day ­ hh:mm Timer: select timer number Status: Disabled/Enabled. If Enabled ­ receiver will be turned on within selected channels at defined "start time" and turned off after "duration" interval Channel type: TV/Radio. If you use multi satellite installation ­ make sure to enter channel number in "All satellites" mode. Channel name: displayed automatically and depends from channel number. Start time: enter start time in format dd/mm/yyyy - day ­ hh:mm Duration: enter duration in hh:mm format. Note: Timer also can be programmed from EPG. See "Program Guide" chapter of this manual. n Press OK to store settings and go back to the previous mode. 5. 2. 6 Factory Default Press OK on `Factory Set' in the Setup Menu. Confirm whether you wish to go back to the factory default settings. This function will return all settings of the receiver to factory default. All your channels, favourite lists and settings will be cleared from the memory. 15 English Sleep Time: 0 ~ 180 min. Receiver will be turned off after selected time interval. PART 1 · English 5. 3 Main Menu Settings From the Main Menu you can access to the Program Guide, Channel Sorting, Language Preference Settings, Favorites Editing, Channel Editing, Conditional Access and Software Version information. n Press n Use n Use MENU CH p/q to move up and down the list. reaching the required menu line, press OK to enter the setting. EXIT to go back to the previous mode. n Upon n Press 5. 3. 1 Program Guide This menu displays same information as described in chapter 8. 4. 4. Press OK on `Program Guide' in the Main Menu. 5. 3. 2 Sort Channels Press OK on `Program Search' in the Main Menu. The following window will appear. n n n n n n Use Vol t/u to select an alphabetical letter. [. . . ] Once you enter to Program Guide the "Now & Next" mode is selected. You can select mode "Schedule" if press Vol u or you can change between TV and Radio list if press Vol t button. Now & Next mode Select "Now & Next" and press OK. Select channel of your choice using CH p/q buttons. [. . . ]