User manual STRONG SRT 7500

[. . . ] Digital High Definition Satellite Receiver SRT 7500 User Manual Picture similar PART 2 · English TAblE of ConTEnTS 1. 0 InTRoDUCTIon 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 YoUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control Unit 2. 4 DEFAULT PIN-CODE: 0000 3. 0 ConnECTIonS 3. 1 Connecting to Satellite Dish 3. 2 Connecting to TV 3. 3 Connecting to Digital Audio Amplifier 3. 4 Connecting to computer by serial cable 4. 0 STARTInG UP foR THE fIRST TIME 4. 1 Language Selection 4. 2 Country Selection 4. 3 Antenna Installation 4. 4 Channel set-up 4. 5 Auto Search 5. 0 MAIn MEnU 5. 1 Program Table 5. 2 Favourites 5. 3 Installation 5. 4 Configuration 5. 5 Timers 5. 6 Games 5. 7 Media Browser 5. 8 CA System 6. 0 oTHER oPERATIonS 6. 1 Electronic Program Guide (GUIDE) 6. 2 Zapping and INFO banner 6. 3 Channel list and viewing mode A. 1 TRoUblESHooTInG A. 2 SPECIfICATIonS APPEnDIX: InSTAllATIon ASSISTAnCE 2 2 3 3 3 4 4 4 4 5 5 5 5 5 5 5 5 6 6 6 6 6 6 7 7 10 10 10 11 11 11 11 12 12 13 14 A1 STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EEC and 73/23EEC RoHS 2002/95EEC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. ASTRA is a registered trade mark of SES ASTRA, Eutelsat and HOT BIRD are registered trademarks of Eutelsat Communications, Irdeto is a trademark of Irdeto Access B. V. , all other product names are trademarks or registered trademarks of their respective owners. 10/2009 1 English PART 2 · English 1. 0 InTRoDUCTIon 1. 1 Safety Instructions The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage with the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Longitude: Enter your local longitude with the nUMERIC buttons. Latitude: Enter your local latitude with the nUMERIC buttons. Turn to Satellite: Turns your antenna to the selected satellite position. Turn to Zero: Turns your antenna to the reference (0. 0) position. note You can set new satellite positions by choosing User Satellites (User 1, 2, 3, 4). LNB Type, Low Frequency and High Frequency: These values are automatically setup for UNIVERSAL LNB configuration and cannot be changed, so other LNB's as UNIVERSAL cannot be supported!LNB Power: Here you can enable/disable LNB supply, use the tu buttons therefore. Adjust this setting to On, if this receiver is not connected to another receiver via loop-through. DiSEqC (Off / Tone A / Tone B / DiSEqC 1 / DiSEqC 2 / DiSEqC 3 / DiSEqC 4): You should set this according to connected switch position of the desired satellite. If your LNB device is connected directly to your receiver, we recommend to select Off mode. Use the u and pq buttons to select and press oK to confirm. Press oK to enter transponder database submenu. This frequency table contains the default transponder database of selected satellite. Use the tu buttons to choose desired function. With bACK you can always cancel actions and exit the actual menu or submenu. The following operations are supported: Add: You can add new transponders to the list (frequency, polarisation, symbol rate). Press oK at Add and use the pq tu buttons for navigation and enter new values with the nUMERIC buttons. Delete: Use the pq buttons to mark the transponder you want to delete. Select Delete with tu buttons and press oK. Select YES, if you want to delete or NO to cancel. Edit: Use the pq buttons to mark the transponder you want to edit. Select Edit with tu buttons and press oK. Now use the pq tu buttons for navigation and enter new values with the nUMERIC buttons. Restore: This function will restore the transponder database to the one which was installed per default. [. . . ] TIMERS: Gives you direct access to the TIMERS menu. PAUSE: Will give you access to the ZOOM menu. Use the buttons described within to perform the different zoom actions. A. 1 TRoUblESHooTInG There may be various reasons for the abnormal operation of the receiver. Check the receiver according to the procedures shown below. [. . . ]