User manual STRONG SRT 5011

[. . . ] Digital Free-To-Air Terrestrial Receiver SRT 5011 User Manual Picture similar PART 1 · English TABLE OF CONTENTS 1. 0 INSTRUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 CONNECTION 2. 1 Connecting to Terrestrial Antenna 2. 2 Connecting to TV and VCR with SCART cable 2. 3 Connecting to TV with RCA cable 2. 4 Connecting to a Digital Audio Amplifier 2. 5 Connecting to PC 3. 0 YOUR RECEIVER 3. 1 Front Panel 3. 2 Rear Panel 3. 3 Remote Control 4. 0 FIRST TIME INSTALLATION 5. 0 MAIN MENU 5. 1 Channel Organiser 5. 2 Channel Search 5. 3 Installation 5. 4 Timer 5. 5 Game 6. 0 OTHER OPERATIONS 6. 1 Mosaic 6. 2 EPG 6. 3 Teletext 6. 4 Subtitles 6. 5 Information A. 1 TROUBLESHOOTING A. 2 SPECIFICATIONS A. 3 GLOSSARY OF TERMS 2 2 2 3 3 4 4 4 4 4 4 5 5 5 6 6 7 7 7 8 11 11 12 12 12 12 13 13 13 14 16 1 English PART 1 · English 1. 0 INSTRUCTION 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: n In a closed or poorly ventilated cabinet; directly on top of or under any another equipment; on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: n To direct sunlight or near any other equipment that generates heat; to rain or intense moisture; to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc. It may cause a fire or an electrical shock. Do not touch a power cord with wet hands. It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards. [. . . ] 5. 3. 1. 7 Factory Default Select Factory default and press OK. Select YES and for the warning "Do you want to set factory default?" press OK, then the receiver will return to its factory default state, and all user data will be deleted. 5. 3. 2 Personal Style In this menu, you can set the Menu Colour, Transparency Level, Border Pattern and Entry Animation. Press UP/DOWN to select the item, and Press LEFT/RIGHT to set the value and OK to confirm. 5. 3. 3 Parental Control In this menu, you can set Channel Lock status (ON or OFF), the Menu Lock status, Parental Setting and change the PIN Code. 5. 3. 3. 1 Channel Lock Set the system Channel Lock to ON or OFF. If the channel lock is ON, the parental PIN code has to be entered correctly before watching the locked channel. 5. 3. 3. 2 Menu Lock Press YES or NO, whether you want to lock the Menu or not and press OK to confirm. If the menu lock is on, you need to enter your PIN for operations such as search program and set factory default. PART 1 · English 5. 3. 3. 3 Parental Setting Set some programs to lock status. If a program is locked, the parental PIN code has to be entered correctly before watching the locked program. Use UP/DOWN keys to select the channel you want to lock and press OK to confirm. 5. 3. 3. 4 Change PIN PIN is Personal Identification Number. To modify the password, you need to enter the current PIN, a new 4 digit password and once again the new one for confirmation; the system password will be changed then. 5. 3. 4 System Information Displays the software version information. 5. 3. 5 System Update 5. 3. 5. 1 Update from Receiver to Receiver You use this menu to update software from receiver to receiver. When it is necessary to update the System, please follow these steps: 1. First power off both receiver, connect them with cross RS-232. Then power on master receiver (master is receiver from which you will copy software) and keep slave receiver off. Navigate in the menu of master receiver and select "System Update ­ STB to STB". When the status displays "detecting slave STB", power on slave STB, after the master STB detects the slave, the master starts transmission and burns. While transmitting and burning, it is very important to avoid other operations such as power off because this may cause destruction of the data in the FLASH memory and the receiver will need to be repaired. When update is complete, first power off both STBs, then disconnect the RS-232 line. [. . . ] Try to adjust your aerial position or wait for the signal to be reestablished Check the connection between receiver and VCR. Please make sure your VCR is set properly The selected program does not support EPG. Set the correct local time Electronic Program Guide (EPG) Blocks in the TV picture A. 2 SPECIFICATIONS Demodulator Demodulator: Transmission mode: Video Decoder Profile level: Video resolution: Decoding & Video Out: Aspect ratio: Audio Decoder MPEG MusiCam Layer I & II Sampling rate: Audio mode: COFDM; 16 QAM / 64 QAM 2 K, 8 K MPEG-2 MP@ML 720 x 576 pixels (PAL), 720 x 480 (NTSC) PAL & NTSC 4:3, 16:9 32, 44. 1, 48 kHz Stereo, Joint Stereo, Dual Mono, Mono 14 PART 1 · English Memory and System Flash memory: SDRAM: 1 MByte 8 MBytes Connectors ANT input - IEC Female TO TV - IEC Male TV SCART: supports RGB, CVBS, Audio Left/Right Output with Volume Control VCR SCART: supports CVBS, Audio Left/Right Output with Volume control 3 RCA for Video (Yellow), Audio Left/Right (Whilte/Red) Coax S/PDIF (Black) Data Interface- serial port: RS-232, 9-Pin D-Sub Male type General Data Supply Voltage: Power Consumption (max): Standby Power Consumption: Operating Temperature: Storage Temperature: Operating Humidity Range: Net-weight: Size (W x D x H) in mm: 90 ~ 240 V AC (SMPS), 50/60 Hz 20 W < 10 W 0 ~ +40 °C -30 ~ +80 °C 10 ~ 85 %, RH, Non-condensing 1. 2 kg 260 x 210 x 40 15 English Tuner Front End: Input frequency range: Loop through frequency range: Input signal level: DVB-T, UHF & VHF Tuner 174 ~ 230 MHz (VHF I/III) and 470 ~ 862 MHz (UHF) 47 ~ 862 MHz -82 ~ -20 dBm PART 1 · English A. 3 GLOSSARY OF TERMS DVB-T MPEG Network PAL PID Digital Video Broadcasting Terrestrial ­ Digital TV via antenna (same as DTTDigital Terrestrial Television). Moving Picture Experts Group is founded by the ISO. [. . . ]