User manual STRONG SRT 5246

[. . . ] Digital Satellite and Terrestrial Receiver SRT 5246 User Manual Picture similar PART 1 · English TABLE OF CONTENTS 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2 2 3 3 4 2. 0 YOUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control Unit 3. 0 CONNECTIONS 3. 1 Connecting to Satellite Dish 3. 2 Connecting to Terrestrial Antenna 3. 3 Connecting to TV & VCR 3. 4 Connecting to Digital Audio Amplifier 3. 5 Connecting to computer by serial cable for downloading software 5 5 5 6 8 8 8 8 8 9 4. 0 STARTING UP FOR THE FIRST TIME 5. 0 MAIN MENU 5. 1 Channel Organiser 5. 2 Satellite set-up 5. 3 Terrestrial set-up 5. 4 Installation 5. 5 Timer 5. 6 Games 6. 0 OTHER OPERATIONS 6. 1 Program Guide (EPG) 6. 2 Zapping and information banners 6. 3 Channel list and view mode A. 1 TROUBLESHOOTING A. 2 SPECIFICATIONS 9 10 10 12 16 17 19 19 20 20 20 20 22 22 1 English PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions Grounding, Polarization -- If this product is used with a specified AC adapter, the adaptermay be equipped with a polarized alternating current line plug (a plug with one blade wider than the other). This safety feature allows the plug to fit into the power outlet only one way. If you cannot insert the plug into the wall outlet, pull it out, reverse it, and then reinsert it. If the plug still fails to fit, contact an electrician and have the receptacle replaced n Protecting the Power Cord -- The power supply cord should be placed so it will not bewalked on. [. . . ] Select item and press OK to setup positioner. More details about Positioner setup read in chapter 5. 2. 1. 1. n if mode of selected dish is "GOTO X" then value is "GOTO X". Select item and press OK to setup GOTO X function. Transponder: move focus of the menu to this item and press OK. List of transponders of selected satellite will appear at right side of the screen. You can select transponder in order to check signal strength and quality of reception. Transponder list contains predefined transponders. If you need to modify transponder list please use menu "Edit satellites" as described in chapter 5. 2. 3. If you need to scan specific transponder then use Manual scan as described in this chapter below. Network search: if this item is set to "OFF" then receiver will search for the channels that are available from preset transponder list of selected satellite. If this item is set to "ON" then receiver in addition will search for the channels from transponders information about that can be found from broadcast. Use this option to get new channels that appeared on satellite. Search for: you can select type of the channels that will be installed to your receiver. n If selected "All channels" then receiver will install Free-To-Air and Scrambled channels n If selected "Scrambled" then receiver will install only Scrambled channels n If selected "FTA" then receiver will install only Free-To-Air channels Once you complete all settings you can start channel search process. Press RED button to setup channels from all transponders of the satellite; Press GREEN button to setup channels from transponder selected in Transponder item; Press YELLOW button to enter to Manual setup channels from specific transponder or to setup single channel with known Video and Audio PID. 13 English PART 1 · English Manual setup of channels In Manual channel search menu you can setup all channels from specific transponder or single channel. To setup all channels from specific transponder: Satellite: Indicate name of the satellite where channels will be searched Frequency: Use Numeric buttons to enter frequency of transponder Polarisation control: Use tupq buttons to select polarisation of transponder Symbol rate: Use Numeric buttons to enter symbol rate value Network search: Use tupq buttons to select ON or OFF Search for: Use tupq buttons to select type of channels to be installed Press RED (Search) button to start channel search. 5. 2. 1. 1 Positioner setup If in Dish setup menu you have configured Dish mode as "DiSEqC 1. 2" then you have to setup position of the dish to each satellite that you want to install. In Channel setup menu move menu focus to Dish position item and press OK button on remote control. Menu Positioner setup will appear on screen. Satellite: Displays the name of satellite position of antenna for which you setup Transponder: Use tu buttons to select reference transponder, receivable in your location, to measure signal strength and quality Movement speed: Use tu buttons to select between Slow and Fast. Slow speed allows you to fine adjust position of the dish. Fast speed can be used to adjust dish position roughly. Move: Use tu buttons to move dish to the East/West direction Centre position: If you press OK button while menu focus is on this item then dish will be turned to centre position, which corresponds to true South direction. [. . . ] TV power off The receiver can't receive the signal Incorrect values of some tuner parameters. Wrong direction of the dish Remedy Check that the power cord is plugged in to the wall outlet Connect the Audio/ Video output of the receiver to TV correctly. Turn TV on Check the antenna cable, replace the cable, or connect the cable to the receiver tightly. Set the values of the tuner parameters correctly in the installation menu. [. . . ]