User manual STRONG SRT 5429

[. . . ] Also, make sure you do not use the unit with a damaged power cord, as this may cause electric shock or fire n n A professional installation is required. If reception is interrupted, contact your authorized local service center 2. 2 Precautions When installing the unit n Install the unit on a level horizontal plane. Unleveled installation may cause damage to the unit The socket-outlet shall be installed near the equipment and shall be easily accessible Do not put heavy items, such as a TV, on top of the unit. That may cause damage to the unit Do not install the unit where: it may be subject to vibrations it is exposed to direct sunlight there is humidity temperature may be too high or too low there is no adequate ventilation n n n n Moving the unit from a cold area to a hot one will cause condensation. [. . . ] "TP ­ NIT" ­ receiver will search channels from one transponder and in addition use network information. This mode recommended if you want to search channels of particular broadcaster only Sub options are: "Free" ­ receiver will search only Free To Air channels "Free+Scr" ­ receiver will search for all channels Transponder: Select index from the stored list Frequency: Polarity: FEC: Function: AGC Signal: Value of transponder frequency in MHz Horizontal / Vertical / Right / Left Auto, 1/2, 2/3, 3/4, 5/6, 7/8 Append / Delete / Change Indicates received signal strength level Symbol Rate: Value of symbol rate in kSymbols Per Second 8. 2. 3. 1 How to search for channels Highlight "Tune method" field and press OK. Names of the found channels will be shown in the two columns: for TV and Radio separately. You can interrupt search process by pressing to OK or EXIT button. If you press OK button: search process will be interrupted and you can select one of the following options: n n Save ­ to save all found channels Unselect ­ to unselect some unwanted channels from the list. Use OK button to unselect channels and Vol t/u buttons to switch between TV and Radio list. Once you finish ­ press EXIT button, select "Save" and press OK. Only selected channels will be stored in the memory n Cancel ­ to cancel result of search. No channels will be stored in the memory If you press EXIT button: search process will be interrupted and no channels stored in the memory. PART 1 l English 8. 2. 3. 2 How to add new transponder Set "Tune method" to "TP" or "TP+NIT" Move focus to "Frequency" and enter value in MHz n Move focus to "Symbol rate" and enter value in kSPS n Move focus to "Polarity" and select value n Move focus to "FEC" and select value or set "Auto" n Move focus to "Function" select "Append" and press OK. Message "Saving data. . . " will be shown on screen. New transponder will be added to the end of the list n n 8. 2. 3. 3 How to delete present transponder Set "Tune method" to "TP" or "TP+NIT" Move focus to "Transponder" and choose transponder you want to delete n Move focus to "Function" select "Delete" and press OK. Once you finish selection of channels, select position in the channel list where to move selected channels and press RECALL button. Press EXIT to return to function selection or continue to move other channels if you want. 8. 3. 4. 2 Add to favourite list To add channel to favourite list highlight icon and press OK. Highlight the channel which you want to add to favourite group and press OK. List of favourite groups will be displayed on screen. Select group of your choice and press OK. Continue to add other channels if you wish. If you wish to remove channel from favourite group select group "[0] ­ unselect". Press EXIT to return to function selection. 8. 3. 4. 3 Lock channel Lock function is designed to give parents possibility to deny access of children to unwanted channels (channels with adult content, for example). It is necessary to know PIN code to watch locked channels. It is recommended to change factory default PIN code to different. To lock channel highlight icon and press OK. [. . . ] Pressing OK on a highlighted channel calls that channel and exits the Channel List. To sort channels in various modes press EXIT while focus of the list is pointed to the channels. If you have multi satellite installation then field with satellite name will be highlighted. Use Vol t/u to select satellite of your choice. [. . . ]