User manual STRONG SRT 6005

[. . . ] Picture simulated PART 1 English Content 1. 0 1. 1 1. 2 1. 3 1. 4 1. 5 2. 0 2. 1 2. 2 2. 3 3. 0 3. 1 3. 2 3. 3 3. 4 4. 0 5. 0 5. 1 5. 2 5. 3 5. 4 5. 5 6. 0 6. 1 6. 2 6. 3 6. 4 6. 5 A. 1 A. 2 A. 3 2 Introduction Safety Instructions Features & Accessories Safety Precautions Storage Equipment Set-up Your Receiver Front Panel Remote Control Unit Rear Panel Connections Connecting to TV & VCR Connecting to Digital Audio Amplifier Connecting to Satellite Dish Connecting to serial cable for downloading software Starting up Main Menu Channel Organiser Installation System setting Timer Game Other operation functions System Information Mosaic (Nine picture view) EPG (Electronic Program Guide) Selection Audio Language Teletext function Trouble Shooting Specifications Glossary of Terms 3 3 4 5 5 6 6 6 7 9 10 10 11 11 13 14 18 19 23 29 39 40 42 42 42 43 45 45 47 48 50 PART 1 English 1. 0 Introduction 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; Directly on top of or under any another equipment; On a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: To direct sunlight or near any other equipment that generates heat; To rain or intense moisture; To any shock which may cause permanent damage to your receiver; To any magnetic objects, such as loudspeakers, transformers, etc. ; To intense vibration; Never open the cover. It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards. Your warranty will be void if the receiver has been opened. [. . . ] If the satellite does not exist in the satellite list, please select "NEW SAT1". SCREEN 20 24 PART 1 English Edit satellite If the parameters of the satellite were changed or the satellite is a new satellite, you must set the parameters of the satellite, such as LNB type, LNB low Freq, LNB High Freq, Transponder, LNB Power, 22 k Tone, DiSEqC and Motor Position. SCREEN 21 Delete satellite If you want to delete a satellite, press the YELLOW key. Then warning message will appear as below. SCREEN 22 Select OK and press the OK key to confirm. 25 PART 1 English 5. 2. 2 Auto Scan SCREEN 23 Press the GREEN key to set the scan mode to Free or Free+CA. Press the YELLOW Key to set the Blind Scan to ON or OFF. Press the BLUE Key to set the scan type to NIT OFF or NIT ON. When the set-up is completed, press the RED key to start the scan, shown as below. SCREEN 24 26 PART 1 English 5. 2. 3 Manual Scan In this menu, you can add a new transponder, edit the transponder or delete the transponder. User can switch satellites with the RED button. SCREEN 25 Add Transponder: In this menu, you can add a new transponder to the system. Press the GREEN button, the Add Transponder sub-menu will appear on screen. Down Frequency: Symbol Rate: Polarity: SCREEN 26 Input the frequency of the new transponder. Input the symbol rate of the new transponder. Select the Polarity of the new transponder. 27 PART 1 English Edit Transponder: In this menu, you can edit a transponder in the system. Press the YELLOW button, the Edit Transponder sub-menu will appear on screen. SCREEN 27 Delete Transponder Press the BLUE button to delete a transponder. The warning massage will be shown as below. SCREEN 28 Press LEFT/RIGHT to select OK, press the OK button to confirm. Scan Press UP/DOWN to select a transponder, press the OK button to scan all the channels on the transponder. 28 PART 1 English 5. 3 System setting In this menu, you can configure the systems such as language Setting, OSD style, Parental Control, TV Settings and Time Setting. SCREEN 29 5. 3. 1 Preference SCREEN 30 29 PART 1 English 5. 3. 1. 1 Language Setting You can change the language of the OSD and Audio. Press UP/DOWN to select the OSD language or Audio language. Press OK/RIGHT to enter the language list and Press UP/DOWN to select the language. Press OK to confirm. SCREEN 31 5. 3. 1. 2 TV settings You can set the TV mode, Screen mode and Video output . SCREEN 32 30 PART 1 English TV mode The TV mode Screen will appear as follows: SCREEN 33 Press OK/RIGHT to select PAL or NTSC, press OK to confirm. If you don't know which standard your TV has, please select AUTO. Screen mode The TV format Screen will appear as follows: SCREEN 34 Press OK/RIGHT to select 4:3 or 16:9, press OK to confirm 31 PART 1 English Video output The Video output Screen will appear as follows: SCREEN 35 Press OK/RIGHT to select CVBS or RGB, press OK to confirm. 32 PART 1 English 5. 3. 1. 3 Time Settings If a broadcaster provides GMT, you can set the time using GMT, or set your own time by yourself. If the GMT usage is ON then the Current time is set automatically or you can set the time zone. If your broadcaster provides the correct time offset then your receiver will change from summertime to wintertime automatically. If you set GMT Usage to OFF, Set Data and Set Time item are displayed. To set the time value manually, move the cursor to the time item and use the numeric buttons on the remote control. SCREEN 36 5. 3. 1. 4 Set Factory Default Please be careful when using this function, because it will erase all the data and parameters you may have set earlier to your receiver. [. . . ] It receives the signals reflected by the dish and converts them to signals that can be used by Satellite receiver. The Moving Picture Experts Group is founded by the ISO. MPEG is a standard method for digital transmission of video and audio. A network which is also known as a bouquet is a set of channels that is offered by a single broadcaster. [. . . ]