User manual STRONG SRT 7100

[. . . ] Digital High Definition Satellite Receiver SRT 7100 User Manual Picture similar 1 3 Fig. 1 2 1 3 6 9 10 Fig. 6 B A C PART 1 • English Table of Contents 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Accessories 1. 5 Usage of external USB devices 2. 0 Your Receiver 2. 1 DEFAULT PIN-CODE: 0000 2. 2 Front Panel 2. 3 Rear Panel 2. 4 Remote Control Unit 3. 0 Connections 3. 1 Basic connection using a Scart cable 3. 2 Basic connection using an HDMI cable 3. 3 Connecting multiple fixed dishes using a DiSEqC 1. 0 switch 3. 4 Connecting and using the IR extender 4. 0 Starting up for the first time 4. 1 Language selection 4. 2 System Setup 4. 3 Satellite Selection 4. 4 Scan Mode 4. 5 Signal Adjust 4. 6 Channel Setup 5. 0 Quick guide to using your receiver 6. 0 Operation 6. 1 Changing channels 6. 2 Info Banner 6. 3 Selection of audio language 6. 4 Teletext 6. 5 Subtitles 6. 6 Changing the video format 6. 7 EPG (Electronic Programme Guide) 6. 8 Instant Recording 6. 9 Timeshift 7. 0 Main Menu 7. 1 Installation 7. 2 Setup 7. 3 Channel 7. 4 Advanced 7. 5 Games 8. 0 TROUBLESHOOTING 9. 0 SPECIFICATIONS STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EEC and 73/23EEC; RoHS 2002/95EEC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. [. . . ] 7. 2. 1 Language Here you can set the preferred Display, Audio and Subtitle languages and Country setting. Use pq to highlight the setting you wish to change and tu to change the value of the highlighted setting. Press OK for a list with all available options for the chosen setting. Display:  This setting affects the menu language of your receiver. All menu’s and messages will be displayed in this language. The receiver will automatically switch audio to is the preferred language whenever available. Subtitle:  Whenever available, subtitles will be displayed in the selected language. Country:  Here you can set your country of residence. 11 PART 1 • English Once all settings are made, press EXIT to leave the Language menu. Press OK to save your settings or EXIT to discard. 7. 2. 2 Output Options This is the menu to configure the audio and video outputs of your receiver. Use pq to highlight the setting you wish to change and tu to change the value of the highlighted setting. Press OK for a list with all available options for the chosen setting. TV Standard:  the standard corresponding to your TV set. Available options are: Auto, Set NTSC, PAL and SECAM. Aspect Ratio:  Use this option to set the aspect ratio of your TV set. Conversion mode:  Use this option to set the preferred way of converting 16:9 broadcasts to 4:3 TV format. You can choose between the following options: Letter-box (the full 16:9 picture will be displayed on your 4:3 TV set with black bars above and below the picture. ), Pan and scan (The centre of the 16:9 picture will be displayed full-screen on your 4:3 TV) and Combined (Combination of Letter-box and Pan and scan. ) SCART Mode:  Select RGB for the best picture quality or CVBS in case your TV doesn’t support RGB. Digital Audio:  Defines the format available on the S/PDIF output of your receiver. When set to PCM, the digital output will always output PCM stereo regardless of the broadcasted audio format. The Auto setting will pass all incoming digital audio through the digital output. Use this option if you have your receiver connected to a digital surround amplifier. [. . . ] Alternatively you can send a support mail via our website: www. strong. tv. NEVER open or disassemble your receiver. This may cause a dangerous situation and will void the warranty. PART 1 • English Symptom The display on front panel does not light up. Remedy Check that the power cord is plugged in to the wall outlet. [. . . ]