User manual STRONG SRT 7300 CI

[. . . ] Digital High Definition Satellite Receiver SRT 7300 CI+ User Manual Bedienungsanleitung Gebruiksaanwijzing Manuel de l'utilisateur Manuale per l'uso Használati utasítás Návod k obsluze Používateľská príručka Picture similar 1 3 Fig. 1 2 4 1 4 7 9 10 Fig. 2 2 3 5 6 8 1 2 3 4 6 9 9 11 13 15 16 18 19 22 23 26 28 17 21 20 25 24 29 27 5 7 8 10 8 12 14 Fig. 6 B A C PART 1 • English Table of Contents 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Accessories 1. 5 Usage of external USB devices 2. 0 Your Receiver 2. 1 DEFAULT PIN-CODE: 0000 2. 2 Front Panel 2. 3 Rear Panel 2. 4 Remote Control Unit 3. 0 Connections 3. 1 Basic connection using a Scart cable 3. 2 Basic connection using an HDMI cable 3. 3 Connecting multiple fixed dishes using a DiSEqC 1. 0 switch 3. 4 Connecting and using the IR extender 4. 0 Starting up for the first time 4. 1 Language selection 4. 2 System Setup 4. 3 Satellite Selection 4. 4 Scan Mode 4. 5 Signal Adjust 4. 6 Channel Setup 5. 0 Quick guide to using your receiver 6. 0 Operation 6. 1 Changing channels 6. 2 Info Banner 6. 3 Selection of audio language 6. 4 Teletext 6. 5 Subtitles 6. 6 Changing the video format 6. 7 EPG (Electronic Programme Guide) 6. 8 Instant Recording 6. 9 Timeshift 7. 0 Main Menu 7. 1 Installation 7. 2 Setup 7. 3 Channel 7. 4 Advanced 7. 5 Games 8. 0 TROUBLESHOOTING 9. 0 SPECIFICATIONS STRONG declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, RoHS 2002/95/EC Subject to alterations. [. . . ] Once all settings are made press GREEN to save or EXIT to quit without saving. Adding a satellite To add a satellite, make sure the highlight is not in the transponders list (press t in case of doubt) and press YELLOW. The procedure for adding a satellite is the same as for editing a satellite. 7. 2 Setup Use the Setup menu to configure the system settings of your receiver. The following sub-menus are available: Language, Output Options, Time Setting, Parental Control and OSD Display. Choose the desired submenu with pq and press OK to advance. 7. 2. 1 Language Here you can set the preferred Display, Audio and Subtitle languages and Country setting. Use pq to highlight the setting you wish to change and tu to change the value of the highlighted setting. Press OK for a list with all available options for the chosen setting. Display:  This setting affects the menu language of your receiver. All menu’s and messages will be displayed in this language. The receiver will automatically switch audio to is the preferred language whenever available. Subtitle:  Whenever available, subtitles will be displayed in the selected language. Country:  Here you can set your country of residence. Once all settings are made, press EXIT to leave the Language menu. Press OK to save your settings or EXIT to discard. 7. 2. 2 Output Options This is the menu to configure the audio and video outputs of your receiver. Use pq to highlight the setting you wish to change and tu to change the value of the highlighted setting. Press OK for a list with all available options for the chosen setting. TV Standard:  the standard corresponding to your TV set. Available options are: Auto, Set NTSC, PAL and SECAM. Aspect Ratio:  Use this option to set the aspect ratio of your TV set. Conversion mode:  Use this option to set the preferred way of converting 16:9 broadcasts to 4:3 TV format. [. . . ] NEVER open or disassemble your receiver. This may cause a dangerous situation and will void the warranty. Symptom The display on front panel does not light up. Remedy Check that the power cord is plugged in to the wall outlet. [. . . ]