User manual STRONG SRT 7335 CI

[. . . ] PART 1 · English TABLE OF CONTENTS 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 YOUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control Unit 3. 0 CONNECTIONS 3. 1 Connecting to Satellite Dish 3. 2 Connecting to TV & VCR 3. 3 Connecting to Digital Audio Amplifier 3. 4 Connecting to computer by serial cable 3. 5 Connecting to external USB - Harddisk 4. 0 STARTING UP FOR THE FIRST TIME 4. 1 Language Selection 4. 2 Select Satellite 4. 3 Dish adjustment 4. 4 Channel set-up 5. 0 MAIN MENU 5. 1 Channel Organiser 5. 2 Satellite Search 5. 3 Installation 5. 4 Timer 5. 5 Application 5. 6 Common Interface 6. 0 OTHER OPERATIONS 6. 1 Program Guide (EPG) 6. 2 Zapping and information banners 6. 3 Channel list and view mode 6. 4 PDR functions A. 1 TROUBLESHOOTING A. 2 SPECIFICATIONS 2 2 3 4 4 5 5 6 7 9 9 10 11 11 12 12 12 12 13 13 13 13 15 18 21 21 22 23 23 23 23 24 26 27 1 English PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage with the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance. Read All Instructions - Before you use the product, read all operation instructions, For more information on accessories such as the lithium ion battery, refer to the manuals provided with those products. Save These Instructions- Save all safety and operating instructions for future reference. [. . . ] Search for: you can select type of the channels that will be installed to your receiver. If selected All channels then receiver will install Free-To-Air and Scrambled channels. If selected Scrambled then receiver will install only Scrambled channels. If selected FTA then receiver will install only Free-To-Air channels. Once you complete all settings you can start channel search process. Press RED button to install channels from all transponders of the satellite; Press GREEN button to install channels from transponder selected in Transponder item; Press YELLOW button to enter to Manual setup channels from specific transponder or to setup single channel with known Video and Audio PID. Manual setup of channels In Manual channel search menu you can setup all channels from specific transponder or single channel. To setup all channels from specific transponder: Satellite: indicate name of the satellite where channels will be searched Frequency: Use 0 ~ 9 buttons to enter frequency of transponder Polarisation control: Use tu buttons to select polarisation of transponder Symbol rate: Use 0 ~ 9 buttons to enter symbol rate value Network search: Use tu buttons to select ON or OFF Search for: Use tu buttons to select type of channels to be installed Press RED (Search) button to start channel search. 5. 2. 1. 1 Positioner setup If in Dish setup menu you have configured Dish mode as "DiSEqC 1. 2" then you have to setup position of the dish to each satellite that you want to install. In Channel setup menu move menu focus to Dish position item and press OK button on remote control. Menu Positioner setup will appear on screen. Satellite: Displays the name of satellite position of antenna for which you setup Transponder: Use tu buttons to select reference transponder, receivable in your location, to measure signal strength and quality Movement speed: Use tu buttons to select between Slow and Fast. Slow speed allows you to fine adjust position of the dish (each press to direction button will turn dish to short angle). Fast speed can be used to adjust dish position roughly. If Movement speed set to Fast press to direction button will cause continuous movement of the dish to appropriated direction, to stop dish you will have to press OK button. Move: Use tu buttons to move dish to the East/West direction Centre position: If you press OK button while menu focus is on this item then dish will be turned to centre position, which corresponds to true South direction. Limits: Use tu buttons to Enable or Disable software limits of your positioner. Set limit: Use tu buttons to select East or West limit of dish movement range. 16 PART 1 · English Step by step recommendations of position setup n Select reference transponder in order to check signal strength and quality during position setup. n If you do not know current direction of your dish then move menu focus to Centre position item and press OK. Knowing your location longitude you may understand direction where necessary to move dish in order to reach position of selected satellite. For example: your longitude is 5° East and you want to setup dish position for ASTRA 1C, 1E (19° East). Then, from centre position, you need to move dish to East direction by pressing to t button. [. . . ] Set the values channel parameters correctly in installation menu. Press TV/RADIO to get back to TV channels. Check whether the batteries are inserted correctly in your remote control. Check the batteries, and if exhausted replace the batteries in the remote control. 26 PART 1 · English A. 2 SPECIFICATIONS Demodulator Demodulation: Input Symbol Rate: FEC Decoder: QPSK, 8-PSK DVB-S QPSK: 1 ~ 45 Ms/s DVB-S2 8-PSK / QPSK: 10 ~ 30 Ms/s 1/2, 2/3, 3/4, 5/6, 7/8 in DVB-S mode; 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10, in DVB-S2 mode Video Decoder Profile Level: Input Rate: Aspect Ratio: Frame Rate: Video Resolution: Audio Decoder Audio Decoding: Audio Mode: Frequency Response: Sampling Rate: MPEG-2 MP@ML, MP@HL, MPEG-4 H. 264/AVC Max. [. . . ]