User manual STRONG SRT 80

[. . . ] Digital Terrestrial High Definition Receiver SRT 80 User manual Bedienungsanleitung Manuel d’Utilisateur Manuale Utente Instrukcja obsługi Manual do Utilizador Picture similar PART 1 • English 01 Jul 2013 15:37 1. 0 Introduction 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Accessories 1. 5 Usage of external USB Hard Disk Devices 2. 0 Your Receiver 2. 1 PIN-CODE DEFAULT: 0000 2. 2 Your receiver 2. 3 Remote Control 3. 0 Connection 3. 1 Connecting to TV Set and Aerial 3. 2 Connecting to Remote sensor and External Power 4. 0 Getting started 4. 1 First Installation 4. 2 Installation 5. 0 Operation 5. 1 Changing Channels 5. 2 Accessing the Electronic Programme Guide (EPG) with EPG button 5. 3 Channel main menu 5. 4 TV Channel Editor 5. 5 Radio Channel list 5. 6 EPG 5. 7 LCN 6. 0 Time 6. 1 Time main menu 7. 0 TV setup 7. 1 TV setup main menu 8. 0 Language 8. 1 Language main menu 9. 0 Others 9. 1 Others main menu 9. 2 Parental Control 9. 3 Update 9. 4 Factory Setting 9. 5 Calendar 9. 6 Calculator 9. 7 Game 9. 8 Information 10. 0 USB 10. 1 USB main menu 10. 2 Multimedia 10. 3 Recorder Setting 10. 4 Device Removed 11. 0 Timeshift and record 11. 1 Timeshift 11. 2 Trick modes 11. 3 Stop the Timeshift 11. 4 Record 12. 0 TROUBLESHOOTING 13. 0 Technical specifications Table of Contents 2 2 2 2 3 3 3 3 3 3 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 7 7 8 8 8 8 8 8 9 9 9 9 9 9 9 10 10 11 11 11 11 11 11 12 12 STRONG declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. All other product names are trademarks or registered trademarks of their respective owners. [. . . ] Once:  one time programming Weekly:  Every week, same day, same time, same channel. Weekend day:  Every Saturday and Sunday, same time, same channel. Weekday: Every Mon, Tue, Wed, Thu, Friday: same time, same channel. Daily:  Every day, same time, same channel. A timer event can be removed with the RED button. Note:  make a recording a USB device must be connected and the timer mode must be set to To ‘Recorder’, otherwise the unit will only wake up on the channel set, but not record. 7. 0 TV setup 7. 1 TV setup main menu The TV setup menu allows you to set TV Format, TVMode, Video Output, TV Resolution, OSD Transparency and Banner Display Time. Press MENU to enter the Main menu and tu to highlight TV Setup, then press q to enter the TV Setup menu. Press pq to highlight the desired item and press OK to enter the sub-menu. TV Format: 4:3PSPan&Scan: When a 4:3 TV should be connected, a 16:9 broadcast will be shown as a centre cut-out, losing image content on the left and the right. 16:9LB Letterbox:  When a widescreen TV is connected, a 4:3 broadcast will be shown with black bars left and right. 16:9FIT:  When a widescreen TV is connected, a 4:3 broadcast will be shown stretched from left to right. 4:3LB Letterbox:  When a 4:3 TV should be connected, a 16:9 broadcast will be shown with black bars above and below, but not losing image content. 7 English function. The default LCN setting is made by the country setting. The default setting can be overruled in this menu, by setting the LCN Mode on/off. PART 1 • English Note:  Some TVs force its screen format to an own setting and cannot always be overruled. TV Mode:  PAL Video Output:  HDMI/SCART(CVBS)/SCART(RGB). Note:  When an HDMI cable is connected to the TV, the unit will automatically switch to HDMI output (“Handshake”), and cut the analogue video outputs, to avoid that the TV switches to Scart input. TV Resolution:  AUTO/1080p_50Hz/720p_50Hz/1080i_50Hz Note:  unit will auto-negotiate with the TV or monitor for the optimum resolution setting The (“Handshake”). OSD Transparency:  The OSD (On Screen Display) can be made transparent in steps 1/2/3/4/5/6/7/8where 1 is very transparent, 8 not transparent. Banner Display Time:  Automatic time-out of the OSD screen. Always On/1S/3S/5S/10S/30 seconds 8. 0 Language 8. 1 Language main menu The language menu allows you to set OSD Language, Audio Language, Subtitle Language and Digital Audio Output. Press MENU to enter the Main menu and tu to highlight TV Setup, then press q to enter the TV Setup menu. Press pq to highlight the desired item and press OK to enter the sub-menu. [. . . ] Press 5 6 to move to the time where you desire to view. Press uto start normal playback. 11. 2 Trick modes During the playback, it is possible to perform the following actions: Press 2 to pause the playback. Press 6 to fast forward the playback. Press GREEN for ‘step’ function. 11. 3 Stop the Timeshift Press 3 to stop Timeshift. 11. 4 Record 11. 4. 1 Instant recording In viewing mode, press RECORD to instantaneously start a recording on the current channel. [. . . ]