User manual STRONG SRT 8010

[. . . ] Digital Terrestrial Receiver SRT 8010 User Manual Picture similar PART 1 · English TABLE OF CONTENTS 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 YOUR RECEIVER 2. 1 Front panel 2. 2 Rear panel 2. 3 Remote control 3. 0 CONNECTION 3. 1 Connecting to terrestrial antenna. 3. 3 Connecting to digital audio amplifier 3. 4 Connecting of external USB memory device 4. 0 FIRST TIME INSTALLATION 4. 1 Language select 4. 2 Terrestrial settings 4. 3 Preferences 4. 4 Adjust antenna 4. 5 Channel setup 5. 0 MAIN MENU 5. 1 Channel organiser 5. 2 Installation 5. 3 Preferences 5. 4 Setup 6. 0 DAILY OPERATIONS 6. 1 Electronic Program Guide (EPG) 6. 2 Channel information 6. 3 Channel list and view mode A. 1 TROUBLE SHOOTING A. 2 SPECIFICATION 2 2 2 3 3 4 4 5 6 7 7 7 8 8 8 8 8 9 9 9 10 10 12 14 15 16 16 17 17 18 19 * 0. 14/Min. from Austrian wired line per February 2008 1 English PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: n In a closed or poorly ventilated cabinet; directly on top of or under any another equipment; on a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: n To direct sunlight or near any other equipment that generates heat; to rain or intense moisture; to intense vibration and to any shock which may cause permanent damage to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc n Do not use a damaged power cord. It may cause a fire or an electrical shock. [. . . ] All parameters are detected automatically. Below of the table with broadcast parameters displayed bars indicated signal level and quality of selected broadcast channel. To start scan on all broadcast frequencies press GREEN (Auto scan) button. To scan one or several broadcast frequencies: select frequency using pqbuttons and press OK to select it. Repeat this for all frequencies you wish to scan. Press RED (Scan selected) button to start scan process. At the end of scan process you can select one of the options described in part 5. 2. 1. 5. 2. 4 Terrestrial Setting In the menu "Terrestrial Setting" you should setup parameters that allow receiver to function correctly in your area. Use buttons tupq to navigate and selection of Country, Antenna Power and Channel numbering. Use button OK to display lists of available options. Country: Select country where receiver is installed. Parameters of broadcast are different from country to country and this parameter is very important. Change of country will delete all installed channels and you need to scan them again. Antenna power: Select "Enabled" if you do use active antenna with support of power injection through coaxial cable. Make sure your antenna supplied by 5 V DC and earns not more than 50 mA. If you use passive antenna or your antenna is powered by an external power ­ select "Disabled" Channel numbering: Select "Appearing order" if broadcast in your country does not support logical channel numbering or select "Operator defined" if broadcast in your country supports logical channel numbering. If you are not sure which option to select ­ please consult to your dealer. To store changes press GREEN (Save) button. 13 English PART 1 · English 5. 3 Preferences In this menu you can setup preferred menu language, audio and subtitles languages, setup video output, time settings and tune some options of OSD display. 5. 3. 1 Language Select OSD language, audio and subtitles languages. To select language use buttons tu or press OK to display list of available options and select language by pq buttons. 5. 3. 2 TV Output To select value use buttons tu or press OK to display list of available options and select value by pq buttons. To store changes press GREEN (Save) button. [. . . ] Short cut in cable between antenna and receiver or antenna is out of service. Remedy Check correct installation of the batteries. Change batteries English Disconnect receiver from main power. Check the cable between receiver and antenna. [. . . ]