User manual STRONG SRT 8300 CI

[. . . ] Digital High Definition Terrestrial Receiver SRT 8300 CI User Manual Picture similar PART 1 · English TABLE OF CONTENTS 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 YOUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 2 Remote Control Unit 3. 0 CONNECTIONS 3. 1 Connecting to Terrestrial antenna 3. 2 Connecting to TV & VCR 3. 3 Connecting to Digital Audio Amplifier 3. 4 Connecting to computer by serial cable 3. 5 Connecting to external USB Hard disk 4. 0 STARTING UP FOR THE FIRST TIME 4. 1 Language Selection 4. 2 Terrestrial Settings 5. 0 MAIN MENU 5. 1 Channel Organizer 5. 2 Terrestrial Search 5. 3 Installation 5. 4 Timer 5. 5 Application 5. 6 Common Interface 6. 0 OTHER OPERATIONS 6. 1 Program Guide (EPG) 6. 2 Zapping and information banners 6. 3 Channel list and view mode 6. 4 PDR functions A. 1 TROUBLESHOOTING A. 2 SPECIFICATIONS 2 2 3 3 3 4 4 5 6 8 8 8 9 9 10 10 10 10 11 11 13 13 15 16 17 17 17 18 18 19 20 21 1 English PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions Grounding, Polarization -- If this product is used with a specified AC adapter, the adaptermay be equipped with a polarized alternating current line plug (a plug with one blade wider than the other). This safety feature allows the plug to fit into the power outlet only one way. If you cannot insert the plug into the wall outlet, pull it out, reverse it, and then reinsert it. If the plug still fails to fit, contact an electrician and have the receptacle replaced n Protecting the Power Cord -- The power supply cord should be placed so it will not bewalked on. [. . . ] Be aware: after pressing BLUE button channel(s) will be deleted from all channel lists. To cancel delete operation you can press EXIT button. Message "Do you want to save?" will appear on screen. English 13 5. 2 Terrestrial Search The Terrestrial Search menu contains following sub-menus: "Channel Setup" and "Terrestrial Settings" In first order make sure that Terrestrial settings are correct and corresponds to the country where you leave. 5. 2. 1 Channel set-up There are 2 possible ways of terrestrial channel search: Auto Scan (RED button) and Manual Scan (GREEN button). n Manual Search Select one or several frequencies by OK button then Manual Scan (GREEN button) to search for channels on selected frequencies. n AutoScan Press Auto Scan (RED) to scan all frequencies in the list. On completing the search, the receiver will save automatically the services information. 5. 2. 2 Terrestrial settings Use pqtu buttons to select your Country, Antenna Supply and Channel Numbering. n Country: With OK you can open the list to select your home country. n Antenna Supply: Select this option to ON in case you use active antenna powered through coaxial cable. The receiver supply DC power +5 V into 50 mA load maximum. n Channel Numbering: select this option to "Operator defined" in case your operator provide logical channel numbering feature. Otherwise select "Appearing order". 5. 3 Installation 5. 3. 1 Preference In this menu, you can set up your personal preferences. n OSD language, Audio language, Subtitle language Use pqtu buttons select the item and OK button to display the list. n Banner Timeout To set banner duration (how long information banner will be displayed on screen). Use pqtu buttons select the item and OK button to display the list. n Transparency Use pqtu buttons to select the transparency level and OK button to display the list. n CAM messages To enable or disable displaying of messages from Conditional Access Module. Disabling of CAM messages could be necessary in order to not disturb you while zapping through channels which can't be descrambled by your smart card. PART 1 · English Power On Channel Use pqtu buttons to select the item. If your choice is Fixed channel: press OK button to display a channel list, select a channel and confirm selection with OK button. Your receiver will always start with defined channel. [. . . ] Another pressing of these buttons will change the speed (FF: x2, x4, x8; FR: x1, x2, x4, x8). To choose a specific position or scene in Timeshift mode press INFO and choose the desired position with the tu buttons. To leave TimeShift press (STOP) button. A. 1 TROUBLESHOOTING There may be various reasons for the abnormal operation of the receiver. Check the receiver according to the procedures shown below. [. . . ]