User manual STRONG SRT 8525

[. . . ] Digital Terrestrial HD Receiver SRT 8525 User Manual USB Recording Channels 400 Up to High Definition Man. / Auto TV Info Search Digital Audio Subtitles Favourite lists 4 30 Timers MP3/JPG MPEG 0. 70 Watt Stand-by Picture similar PART 2 • English Table of Contents 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Accessories 1. 5 Usage of external USB devices 2. 0 Your receiver 2. 1 Front panel 2. 2 Rear panel 2. 3 Remote control 2. 4 Installing the batteries 2. 5 Using the remote control 3. 0 Connections 3. 1 Connecting to your aerial antenna 3. 2 Connecting to TV with HDMI cable 3. 3 Connecting to TV with SCART cable 3. 4 Connecting to TV with cinch cable 3. 5 Connecting to a digital audio amplifier 3. 6 Connecting to a digital A/V receiver and TV using HDMI 3. 7 Connecting an external USB storage device 4. 0 Starting up for the first time 4. 1 Antenna Adjustment 5. 0 Quick guide to using your receiver 5. 1 Changing channels 5. 2 Adjusting volume and audio 5. 3 Info Banner 5. 4 Electronic TV Programme Guide (EPG) 5. 5 Selecting subtitle language 5. 6 Displaying Teletext 5. 7 Using external USB storage devices 5. 8 Instant Recording 5. 9 Playback of recording 6. 0 Main Menu 6. 1 Programme Organizer 6. 2 Channel search 6. 3 System Setup 6. 4 Tools 6. 5 Records 6. 6 Multimedia 6. 7 Irdeto CA Status 7. 0 Troubleshooting 8. 0 Technical specification 9. 0 Appendix 27 Nov 2012 14:46 STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EC and 73/23/EC, RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. Irdeto is a registered trademark of Irdeto Access BV. All other product names are trademarks or registered trademarks of their respective owners. [. . . ] Press MENU and use tu to select Channel Search, then press OK. Following submenus will be displayed: Search Setup, Auto Search and Manual Search. Use pq to select a submenu and press OK or u to access. 6. 2. 1 Search Setup In the menu Search setup you can set the antenna power and the country in which you live. Country: Use the tu buttons to change the country. Antenna Power: If you use an antenna that can be amplified (i. e. an active indoor/ outdoor antenna) and it requires a voltage of 5 V and doesn’t consume more than 60 mA, then you can set the antenna power to On. If you use an antenna without an amplifier or your antenna is already amplified by an external power supply or if you use an antenna from a house distribution system, please keep the antenna power Off. 6. 2. 2 Auto Search After selecting this menu item and pressing OK you will be asked to enter the PIN code (DEFAULT PIN: 0000) in order to update the current channel list. If you don’t want to perform a full channel scan you can press EXIT to cancel. After entering the PIN code (DEFAULT PIN: 0000) the receiver will perform an automatic channel search through all frequencies and after finishing this process it will update the channel list. During the search process the receiver will display the progress bar, the currently scanned frequency and the channel names. The receiver will add all new found channels to the channel list. 6. 2. 3 Manual search In this menu you can search for channels on a specific frequency or channel. This menu requires knowledge of some parameters in order to search on the correct channel/frequency in your area. Scan mode: Use tu to choose between By Channel and By Frequency. If you set the scan mode By Channel, then the following is available: Band: Use tu to choose UHF (Ultra High Frequency) or VHF (Very High Frequency). Frequency channel: Select a frequency channel on which you would like to search for the channels. If you set the scan mode By Frequency, then the following is available: Frequency: Use 0-9 to enter the frequency on which you would like to search for channels. 12 PART 2 • English For the VHF frequency band commonly used 7 MHz, for UHF frequency 8 MHz is used. Signal level and quality indicators will help you ensure that you have signal on the selected frequency channel or frequency entered, as well as to adjust the antenna, if necessary. After you have entered the settings correctly you will need to select Search (directly above the signal bars) and press OK. [. . . ] Remedy Check the connection of the receiver to the main power. Turn the power extender ON. 7. 0 Troubleshooting No signal found Connect the antenna cable. Make sure that the cable is in good condition. Make sure to enable antenna power from the receiver menu (see chapter 6. 2. 1) or use an external power supply. [. . . ]