User manual SUB-ZERO 249FF-PS

[. . . ] Planning Information Undercounter Model 249FF (I ) All Freezer Serial and model number plate Interchangeable door hinge Automatic ice maker (249FFI) Adjustable temperature control Removable ice bucket (249FFI) Model 249FF One piece interior Interior light Four-sided magnetic gasket Model 249FFI with Ice Maker Front venting with removable kickplate Removable wire shelves Aside from the full-size units Sub-Zero offers in its Built-In and Integrated lines of refrigeration, we round out our product line-up with a line of traditional Undercounter refrigeration which meets all of the exacting standards you have grown to expect from Sub-Zero. If you desire, this unit could be matched with a 249RP and outfit a compact New York apartment with all the refrigeration space necessary. [. . . ] To obtain local dealer information, visit the Locator section of our website, subzero. com. A line filter is required when water conditions have a high sediment content. The ice maker operates on water pressure of 20 psi (1. 4 bar) to 100 psi (6. 9 bar). In some cases a reverse osmosis water filter system may not be able to maintain the minimum water pressure consistently. A 115 V AC, 60 Hz, 15 amp fused electrical supply is required. It is recommended that a separate circuit, serving only this appliance, be provided. All Undercounter models are equipped with a power supply cord with a 3-prong grounding plug which must be plugged into a mating 3-prong grounding type wall receptacle. Locate electrical within the shaded area shown in the illustration on page 3. You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. Refer to the Undercounter Installation Instructions packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Undercounter Model 249FF (I ) F R A M E D PA N E L S Framed door panels must be 1/4" (6) thick around the perimeter. If the panel is thicker than 1/4" (6), an edge must be routed around the panel to ensure a proper fit. Refer to the illustrations on this page. PANELS 1/4" (6) THICK OR LESS IMPORTANT NOTE: The weight of the panel cannot exceed 20 lbs (9 kg). Trim reveal 1/4" (6) min F R A M E D PA N E L D I M E N S I O N S WIDTH 1/4" (6) HEIGHT Panel Door Panel Handle Recess Location (A) 23 5/8" (600) 30 " (762) 15" (381) 20 lbs (9 kg) Framed door panel 1/4" (6) thick or less Maximum Panel Weight PANELS THICKER THAN 1/4" (6) Trim reveal 1/4" (6) min Rout to 1/4" (6) thickness Framed door panel thicker than 1/4" (6) 4" A H W Framed Door Panel Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Undercounter Model 249FF (I ) O V E R L AY PA N E L OVERLAY PANEL Rear View 1/8" (3) 5/16" (8) The overlay door panel design allows for a decorative panel to cover the door trim for a more seamless appearance. To achieve this look, the most common way is to work with three panels ­ the decorative 3/4" (19) thick overlay panel, a 0. 10" (3) thick spacer panel and a 1/4" (6) thick backer panel. An accessory kit (OVERPAN) is required in order to accommodate the proper installation of the overlay panel. [. . . ] Refer to the overlay panel specifications below. 1" Notch Required for Hinge Clearance (top and bottom) (25) Notch required for hinge clearance H IMPORTANT NOTE: The weight of the panel assembly cannot exceed 20 lbs (9 kg). IMPORTANT NOTE: The total thickness of all panels for an overlay model must be at least 5/8" (16) thick. W Overlay Door Panel O V E R L AY PA N E L D I M E N S I O N S WIDTH HEIGHT Door Panel Door Spacer Door Backer 24" (610) 23" (584) 23 5/8" (600) 30 5/16" (770) 29 3/8" (746) 30" (762) 20 lbs (9 kg) Maximum Weight (panel assembly) Dimensions in parentheses are in millimeters unless otherwise specified. 6 Planning Information Undercounter Model 249FF (I ) O V E R L AY PA N E L 145° DOOR OPENING (TOP VIEW) 24" (610) CABINETRY OPENING *MODEL 249 OVERLAY MUST EXTEND A MINIMUM OF 1-13/16" (46) BEYOND SURFACE OF ADJOINING CABINETRY AND MUST BE 1" (25) FROM ADJACENT CABINETRY TO ALLOW THE MAXIMUM DOOR SWING DOOR CLOSED 1"* (25) 3/4" (19) 113/16" (46) DOOR PANEL DOOR PANEL DOOR OPEN @ 145° 145°* Dimensions in parentheses are in millimeters unless otherwise specified. 7 [. . . ]