User manual SUB-ZERO 315 ICE MAKER E

[. . . ] installation and operation MODEL 315 ice maker ® InTRODUCTION Contents Introduction . 23 The Sub-Zero Model 315 is a restaurant-type ice maker designed for home use. It produces the same high quality clear ice that you would expect from Sub-Zero. This guide is intended as a resource for the installation and operation of the Model 315. [. . . ] weight limit Remove the handle side bracket attached to the front of the door and set aside. Place the door panel lying face down on a protected surface to ensure the front is not scratched or damaged. Position the plastic template provided flush with the upper edge of the door. Be sure you are following the exact location for the RH or LH door position. IMPORTANT NOTE: Remember you are viewing the door panel from the back side in the illustrations. The overall size of the panel shown is the minimum size necessary to cover the door of the unit. The exact measurements of your door panel may vary depending on the particular installation you are following. Once you have located the proper position for the hardware, mark the holes, remove template, and drill pilot holes for mounting of the hardware. We recommend starting the first few holes, positioning the hardware, drilling remaining pilot holes, and securing the mounting brackets with the #8 x 1/2" screws. Install the door panel by engaging the tabbed bracket to the door first and then sliding the hinge side hardware over the positioning screws. You will have a 1/4" inch adjustment, up and down, side to side, with this hardware. Once you have the door in place, attach the remaining #8 x 1/2" screws to the hinge side mounting bracket and install decorative caps. CAUTION Where the reveal on the hinge side of the door panel is less than 1/4", and the panel has a square corner, severe finger pinching or damage to the appliance may occur. Flush with Top and Side of Panel Top Ed Upper Br Right Ha acket nd Sw ing ge of Do or Pane l Upper Br Left Ha acket nd Sw ing Door P anel Drillin g Tem plate Right-Hand Door Panel Left-Hand Door Panel Handle Si Left Ha de Bracke t nd Sw ing Handle Si Right de Bracke Hand t Swing Befor e determ drilling so scr ine fina inset pan els or sty ews fall l placement , within les. rails CAUT ION Lowe r Brac ket Template Positioning 11 INSTALLATION 90 Degree Door Stop Hinge Cover Installation Model 315 has a 90 degree door stop. Follow these steps for installation: 1) Open door to 80 degrees. 2) Insert stop pin into the bottom door hinge (pin enters from the top). 3) Pin must be driven until head has made contact with the hinge body. 4) Insert stop pin into the top door hinge (pin enters from the bottom). 5) Pin must be driven until head has made contact with the hinge body. 7) Install hinge covers if installation is complete. This is to be completed after the unit is fully installed. IMPORTANT NOTE: Install the 90 degree stop prior to installing the hinge covers. 1) Remove the backing paper of the adhesive pads and bond to the hinge as shown in the illustration. IMPORTANT NOTE: Hinges must be free of dirt or grease before applying covers. 2) Install center covers as shown in the illustration (magnets will secure these covers). [. . . ] Replace the control box cover and kickplate. Reconnect the electrical power. Icemaker Control Knob OFF LOW ICE LEVEL CON TROL HIGH NORMAL 6) 7) 8) WARNING Ice Maker Control Knob Electrical Shock Hazard Disconnect electrical power before beginning removal of parts. Harvest Time Adjustment 19 TROUBLESHOOTING Problem Possible Cause Probable Correction The ice maker does not operate The ice maker is unplugged Breaker tripped or fuse is blown Plug the ice maker in Reset breaker/replace fuse ­ if it happens again, call for service to check for a short circuit in the ice maker Turn ice maker control to ON Ice on sensor tube ­ its then normal for the ice maker to be off Ice maker in a room below 50°F ­ room needs to be warmer for ice maker to operate. Bin thermostat stuck open, needs to be replaced. Ice maker control turned to OFF Bin thermostat open, keeping ice maker off Timer contacts open Cubes are too big Cubes are too small Cube size control set too cold Cube size control set too warm Not enough water Replace timer Adjust cube size control for a smaller cube Adjust cube size control for a larger cube Check water supply ­ filter may be restricted Check inlet water valve ­ inlet screen may be restricted Cube size control stuck closed ­ timer runs all the time. Cubes are partially formed ­ have ragged sides Ice maker makes ice, but bin does not fill up with ice Spray jets partially clogged Replace timer Clean ice making system with ice maker cleaner. [. . . ]