User manual SUB-ZERO 315-PS

[. . . ] Keep in mind that special plumbing requirements are necessary to install and have this unit function properly. Aside MODEL 315I(P) Undercounter ice maker Model 315I has a gravity drain, while Model 315IP has a built-in pump to allow water to drain into adjacent sink 24" (610) depth-true design for a complete integrated look Door accepts custom panels Automatic ice maker provides high-quality, clear ice Ice storage capacity of up to 26 lbs (12 kg) Automatic defrost Reversible door swing Front venting with removable kickplate allows unit to be serviced from the front Solid core door with magnetic gasket and door closer UL approved for US and Canada Two, five and twelve year residential warranty-- exclusions apply; warranty information can be found on our website, subzero. com Dimensions in parentheses are in millimeters unless otherwise specified. 11/06 1 Planning Information Undercounter Model 315 l ( P) S P E C I F I C AT I O N S Model 315I(P) Overall Width Overall Height Overall Depth MODEL OPTIONS Undercounter Ice Maker 15 3/16" (386) 33 5/8" (854) 24" (610) 26 lbs (12 kg) 33 3/4" (857) 15 1/4" (387) 115 V AC, 60 Hz, 15 amp circuit 100 lbs (45 kg) Optional stainless steel door panels are available in 15" (381) and 18" (457) widths Ice Maker without Pump Ice Maker with Drain Pump 315I 315IP Ice Storage Capacity Minimum Height Required Door Swing Clearance PA N E L O P T I O N S Electrical Requirements Shipping Weight /S /P /B Special Note Custom Integrated Wood Panel Classic Stainless Steel Finish Platinum Stainless Steel Finish Carbon Stainless Steel Finish Stainless steel door panels are ordered and shipped as a sales accessory and include a tubular handle. Specifications are subject to change without notice. ACCESSORIES Filler strip for 18" (457) openings Accessories are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. OVERALL DIMENSIONS 2 1/8"(54) 15 3/16" (386) (483) 19" 33 5/8" (854) 29 3/8" (746) 33 5/8" (854) DOOR SWING 115° 4"(102) 15 3/16" (386) (483) 19" FRONT VIEW SIDE VIEW S TOP VIEW Dimensions may vary by ± 1/8" (3). [. . . ] Specific step-by-step instructions are included with the drain pump kit. Contact your Sub-Zero dealer for details. To obtain local dealer information, visit the Locator section of our website, subzero. com. The drain and inlet water tubes must be plumbed before connecting to the ice maker. For the gravity drain, all horizontal runs of drain lines must have a 1/4" (6) per 1' (305) fall. An air gap will likely be required between the ice maker drain tube and the drain / waste receptacle. A stand pipe with a trap below it would be acceptable for the drain / waste receptacle. Refer to the installation illustrations for the Model 315I (gravity drain) and the Model 315IP (drain pump) on page 3. For Model 315I (gravity drain), the drain must be located in a 2" (51) area centered in the opening for the unit, 23" (651) back from the front door. Poor draining will cause a high rate of ice melting in the bin. 1/4" Rough in the water supply line. Connect a OD copper line to the house supply, being sure to use an easily accessible shut off valve between the supply and the unit. A saddle valve kit (4200880) is available from your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. A line filter is required when water conditions have a high sediment content. [. . . ] In addition, be aware of local codes and ordinances when installing your service. Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Undercounter Model 315 l ( P) D O O R PA N E L It is important to understand the differences in mounting any wood panel to Model 315I(P). The panel must be 5/8" (16) minimum thickness. Refer to the installation instructions packaged with the unit to understand how the panel is installed. [. . . ]