User manual SUB-ZERO 315IP

[. . . ] MODELS 315I AND 315IP ICE MAKER INSTALLATION & OPERATION CONTENTS Models 315I and 315IP Installation Installation Checklist Models 315I and 315IP Features Models 315I and 315IP Operation Troubleshooting Guide Service Information Sub-Zero Warranty 4 13 14 15 20 22 23 Features and specifications indicated herein and on the website are subject to change at any time without notice. Check our website, subzero. com, for the most up-to-date specifications. As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Sub-Zero equipment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation. SUB-ZERO ® is a registered trademark of Sub-Zero Freezer Company, Inc. S U B - Z E R O M O D E L S 3 1 5 I A N D 3 1 5 I P I N S TA L L AT I O N A N D O P E R AT I O N T H A N K YO U Congratulations on the purchase of your Sub-Zero Model 315I ice maker (Model 315IP with drain pump). [. . . ] Instructions regarding sizing of the door panel are provided in the Sub-Zero Design Guide. For door handle hardware, a D-style pull centered on the edge opposite the door hinge side is recommended. Screw heads may have to be countersunk to ensure that the hardware does not interfere with the panel fitting flush with the unit door. MODELS 315I AND 315IP Door Panel Width ­ 1/8" (3) reveal Door Panel Height ­ 4" (102) toe space 1/8" Remove the handle side bracket attached to the front of the door and set aside. Place the door panel lying face down on a protected surface to ensure the front is not scratched or damaged. Position the plastic template provided flush with the upper edge of the door. Be sure you are following the exact location for the RH or LH door position. IMPORTANT NOTE: Remember you are viewing the door panel from the back side in the illustration. The overall size of the panel shown is the minimum size necessary to cover the door of the unit. The exact measurements of your door panel may vary depending on the particular installation you are following. Once you have located the proper position for the hardware, mark the holes, remove template, and drill pilot holes for mounting of the hardware. We recommend starting the first few holes, positioning the hardware, drilling remaining pilot holes, and securing the mounting brackets with the #8 x 1/2" screws. Refer to the illustrations below. PA N E L DESIGN Additional panel design information can be found in the Sub-Zero Design Guide. Check our website at subzero. com. 15" (381) 30 3/8" (772) 5/8" (3) reveal (16) min Door Panel Thickness Door Panel Weight 15 lbs (6. 8 kg) max _ Dimensions may vary + 1/8" (3). Flush with Top and Side of Panel Right-hand door panel Left-hand door panel Template position 11 S U B - Z E R O M O D E L S 3 1 5 I A N D 3 1 5 I P I N S TA L L AT I O N I N S TA L L AT I O N 9 0 - D E G R E E D O O R S TO P Exercise caution when drilling holes for mounting hardware. This is especially critical with inset panels. Model 315I(P) has a 90-degree door stop. Follow these steps for installation: 1) Open the door approximately 80 degrees. 2) Insert the stop pin into the bottom door hinge (pin enters from the top). The pin must be inserted until the head has made contact with the hinge body. 3) Insert the stop pin into the top door hinge (pin enters from the bottom). H I N G E C O V E R I N S TA L L AT I O N Install the door panel by engaging the tabbed bracket to the door first and then sliding the hinge side hardware over the positioning screws. You will have a 1/4" inch adjustment, up and down, side to side, with this hardware. Once you have the door in place, attach the remaining #8 x 1/2" screws to the hinge side mounting bracket and install decorative caps. If the reveal on the hinge side of the door panel is less than 1/4", and the panel has a square corner, severe finger pinching or damage to the unit may occur. IMPORTANT NOTE: Install the hinge covers after installation of the ice maker is complete. [. . . ] If you provide us with your e-mail address, we will send you exciting new product updates and recipes as they become available, along with information on special events. Sub-Zero Dealer and Phone B E F O R E C A L L I N G F O R S E RV I C E Before calling a Sub-Zero authorized service center, refer to the Troubleshooting Guide on pages 20­21. Check the household fuse or circuit breaker to see if it has been blown or tripped and that the electrical connection to the appliance has not been disconnected. A power outage may also have caused a disruption in service. The information and images in this guide are the copyright property of Sub-Zero Freezer Company, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Sub-Zero Freezer Company, Inc. [. . . ]