User manual SUB-ZERO 400 INSTALL GUIDE

[. . . ] W INE S TORAGE INSTALLATION INSTRUCTIONS S U B - Z E R O W I N E S TO R AG E The importance of the installation of the Sub-Zero Wine Storage unit cannot be overemphasized. Installation should be done by a qualified installer. CONTENTS Models 424 and 424FS Installation Models 427 and 427R Installation Model 430 Installation Installation Checklist Service Information 3 12 24 34 35 Before you begin the installation process, it is recommended that you read this entire Installation Instructions book. There are key details that you should take special care to observe during the installation. [. . . ] Check our website at subzero. com. The stainless steel panel is mounted to the door by passing the #8­32 x 5/8" screws provided, through holes in the door frame from the rear, and into the threaded holes in the door panel. The screw holes inside the door are hidden under a cover flap on the door gasket. It is necessary to lift the flap to insert the screws. After the door panel is installed, apply the cover tape patches provided, over the holes on the inside surface of the door. For installation of stainless steel panels on Model 427R drawers, see Model 427R Drawer Panels on page 22. The cover plugs or patches are part of the insulation system on the door of the Wine Storage unit. Be sure to cover all the holes in the door that were used. Gasket 13/32" (11) Diameter Stainless Steel Panel Door Frame Glass Integrated Panel Door Frame 1/4" (6) Diameter Back of Stainless Steel Panel Illus. 11 20 M O D E L S 4 2 7 A N D 4 2 7 R I N S TA L L A T I O N MODELS 427 | 427R With the Wine Storage unit secured in position and the door closed, the panel is held in the desired position on the door and rapped by hand from the front, putting center marks on the rear surface of the panel. If the door panel is made of such a material that pre-drilling is needed, all of the mounting holes should be marked. If not, only enough holes to hold the panel in place temporarily, are necessary. The door panel is then lowered from the door frame, tenon centers removed, the door opened and the screws driven into the panel through the black tape on the door frame, using the center marks to locate the screws. The screw holes inside the door, are hidden under a cover flap on the door gasket. It is necessary to lift the flap to insert the screws. Use as many screws as necessary to hold the door panel in place properly. IMPORTANT NOTE: After the first three or four mounting screws are in place, but not completely tightened, close the door and check your panel fit. This is the time to make small adjustments. Once you are satisfied with the appearance, open the door and apply the remainder of the screws. The metal frame on the glass door has numerous mounting holes on each side of the door. This is to accommodate the Sub-Zero accessory handles and provide for easy attachment of the handle through the door frame. If you choose not to use the pre-drilled handle mounting holes, it will be necessary to fasten the handle from the rear of the door panel only, or drill one or more additional holes through the metal frame of the glass door. Illustration 12 on page 20, shows how this hole passes through the door frame. The hole center is on the small locator groove in the front of the frame. A 1/4" (6) diameter hole is made in the front wall of the extrusion and a 13/32" (11) diameter hole through the rest of the frame. The wine storage unit door is made with a sealed double wall tempered glass core. [. . . ] 17 Dimensions in parentheses are in millimeters unless otherwise specified. Illus. 18 34 S E RV I C E I N F O R M A T I O N S E RV I C E I N F O R M A T I O N I N S TA L L A T I O N C H E C K L I S T Has the packing material been removed?Turn the unit on first, is the unit operating properly?Has the unit been secured in place with an anti-tip bracket or by a secure overhead cabinet or structure? [. . . ]