User manual SUB-ZERO 424-PS

[. . . ] Dimensions in parentheses are in millimeters unless otherwise specified. 2 Planning Information Wine Storage Model 424 S P E C I F I C AT I O N S Model 424 Overall Width Overall Height Overall Depth MODEL OPTIONS Undercounter Wine Storage Unit 23 7/8" (606) 34 " (864) 24" (610) 46 Bottles (750 ml) 34 1/4" (870) 25 3/8" (645) 115 V AC, 60 Hz, 15 amp circuit Overlay ­ 190 lbs (86 kg) Stainless Steel ­ 195 lbs (88 kg) High altitude glass door is available for elevations 5, 000' (1524 m) or above Overlay Design Classic Stainless Steel 424__/O 424__/S Wine Storage Capacity Minimum Height Required Door Swing Clearance Electrical Requirements DOOR OPTIONS Shipping Weight 424G/__ Special Note Full-View Glass Door High Altitude Glass Door 424HAG/__ You must allow 90 days from order to delivery for high altitude glass door unit. Specifications are subject to change without notice. ACCESSORIES Tubular handles in classic, platinum and carbon stainless steel Polished chrome handle for overlay design UL approved door lock kit Accessories are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. Dimensions in parentheses are in millimeters unless otherwise specified. 3 Planning Information Wine Storage Model 424 I N S TA L L AT I O N S P E C I F I C AT I O N S 24" (610) ROUGH OPENING DEPTH TOP VIEW 24"(610) ROUGH OPENING WIDTH ANTI-TIP BRACKET 341/2" (876) ROUGH OPENING HEIGHT 341/4" (870) MINIMUM HEIGHT REQUIRED LOCATE ELECTRICAL WITHIN SHADED AREA 151/2" (394) E 21/2" (64) 41/2" (114) FRONT VIEW DIMENSIONS Finished Rough Opening Width Finished Rough Opening Height Finished Rough Opening Depth Location of Electrical See Installation Instructions shipped with unit for detailed specifications. 24" (610) 34 1/2" (876) 24" (610) Within shaded area Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Wine Storage Model 424 I N S TA L L AT I O N N OT E S Refer to the illustrations and specifications for overall dimensions, finished rough opening dimensions and installation specifics. The Wine Storage unit must be installed to open a minimum of 90° or you will have problems pulling the shelves out. For corner installations, you need allow for a minimum 3" (76) filler so the door can open to 90°. [. . . ] It is recommended you use our optional handles and use the pre-drilled holes supplied to locate the handles within the frame of our unit. Refer to page 8 for specifics about installing handle hardware. For Model 424, the weight limit for the door panel frame is 10 lbs (5 kg). Sub-Zero has provided a natural cherry wood facing to each of the wine shelves. You can choose to replace these strips with wood more complementary to your design and surrounding cabinetry. Refer to the full-scale illustration on page 10 for dimensions on the wood facing. A 115 V AC, 60 Hz, 15 amp fused electrical supply is required. It is recommended that a separate circuit, serving only this appliance, be provided. All Sub-Zero Wine Storage units are equipped with a power supply cord with a 3-prong grounding plug which must be plugged into a mating 3-prong grounding type wall receptacle. Locate electrical within the shaded area shown in the installation illustration on page 4. You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. Refer to the Wine Storage Installation Instructions packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Wine Storage Model 424 I N T E G R AT I N G C A B I N E T RY Unless you are installing a stainless steel unit, you will need to provide a door panel frame for the glass door. If you order a stainless steel unit, the Model 424 will be shipped with panels and hardware installed. O V E R L AY PA N E L S A solid panel must not be installed on a glass door unit, as this may cause moisture to form behind the panel. The overlay panel applied to Model 424 should not be confused with the Built-In overlay panel application. The overlay panel will consist of only a frame and would be either the 5/8" (16) or 3/4" (19) panel you may be using. It is affixed directly to the door itself with screws through a series of pre-drilled holes in the perimeter of the door itself. You do not need any backer or spacer panel. The glass door opening of the Model 424 is designed to be exposed to room air circulation. Decorative overlays on the glass should be kept to a minimum. Also, rails and stiles can be increased in size but should not exceed cabinet manufacturers standard width. [. . . ] The metal frame on the door has numerous mounting holes on each side to accommodate Sub-Zero accessory handles. This will allow you to provide the best possible handle alignment and not take away from the strength of the stile in this area after the unit is used a number of times. We recommend using a pull handle and not a pull knob. If you elect to place different hardware on these units, we encourage you to fasten the hardware by passing through our door and attach the hardware through the Sub-Zero door's frame. [. . . ]