User manual SUB-ZERO 700BF-PS

[. . . ] To obtain local dealer information, visit the Locator section of our website, subzero. com. Dimensions in parentheses are in millimeters unless otherwise specified. 3 Planning Information Integrated Model 700 BF (I ) I N S TA L L AT I O N S P E C I F I C AT I O N S TOP VIEW ANTI-TIP BRACKET* TOP VIEW 6" (152) 11/2" (38) (635) 25" 13 1/2" (343) 15 1/2" (394) 9" (229) (686) 27" 13 1/2" (343) ANTI-TIP BRACKET (686) 27" WATER LINE BOTTOM ENTRY LOCATION *PLACEMENT OF THE ANTI-TIP BRACKET SHOULD BE 24" (610) FROM THE FRONT OF THE UNIT WITHOUT PANELS TO THE BACK OF THE ANTI-TIP BRACKET. WATER LINE SIDE ENTRY LOCATIONS 11/2" (38) 11/2" (38) (686) 27" (635) 25" 341/2" (876) NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO PREVENT UNIT FROM TIPPING FORWARD ANTI-TIP BRACKET WATER LINE SIDE ENTRY LOCATION FRONT VIEW LOCATE ELECTRICAL WITHIN SHADED AREA ­ ORIENT GROUND PRONG TO RIGHT AS SHOWN ANTI-TIP BRACKET LOCATE WATER LINE (REAR ENTRY) WITHIN SHADED AREA SIDE VIEW 4 1/2" (114) 3" (76) 1/4" (6) 13" (330) 2 1/2" (64) 15 1/2" (394) 9" (229) 3/4" (19) DIMENSIONS Finished Rough Opening Width Finished Rough Opening Height Finished Rough Opening Depth Location of Electrical Location of Plumbing 27" (686) 34 1/2" (876) 25" (635)* Within shaded area Within shaded area * The depth of the Model 700BF(I) is 24" (610) from the front of the unit to its back. Your design may necessitate moving the unit back, or cabinets forward to achieve a flush fit. This will require a minimum rough opening depth of 25" (635). See Installation Instructions shipped with unit for detailed specifications. [. . . ] The ice maker operates on water pressure of 20 psi (1. 4 bar) to 100 psi (6. 9 bar). In some cases a reverse osmosis water filter system may not be able to maintain the minimum water pressure consistently. When routing the water through the side walls, you must place the water line within 1/2" (13) of the floor and as close as possible to the back wall. The line must be routed around the anti-tip bracket so it clears the bracket and leveling feet of the unit. Refer to the installation illustration on page 4 for placement of the water line. Do not route water supply line in front of the compressor tray. The tray must be slid forward for service. Regardless of the routing, allow for 27" (686) of excess copper tubing to remain outside the wall or floor for easy connection to the unit, as shown in the installation illustration. A 115 volt, 6OHz, 15 amp circuit breaker and electrical supply are required. A separate circuit, servicing only this appliance is necessary. All Integrated models are equipped with a power supply cord with a 3-prong grounding plug, which must be plugged into a mating 3-prong grounding type wall receptacle. The electrical outlet must be placed so the grounding prong is to the right of the thinner blades. The outlet must be flush with the back wall. Locate electrical within the shaded area shown in the installation illustration on page 4. Do not use an extension cord or two prong adapter. Electrical ground is required on this appliance. Do not under any circumstances remove the power supply cord ground prong. You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. The Integrated Refrigeration Installation Instructions packed with the appliance will give you step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Integrated Model 700 BF (I ) C A B I N E T RY A P P L I C AT I O N S Integrated refrigeration is compatible with virtually any style and look of cabinetry. The models can be used with framed as well as frameless cabinets. Because of the precise application and the look you may want to achieve, there are important questions you need to answer before ordering panels for the drawers. [. . . ] This optional component is available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. T 54 (1372) TOP VIEW Installation of two units side by side. C CABINETS 25 (635) 2 M 27 (686) MINIMUM 5/8" (16) SIDE PANELS Installation at end of run. Dimensions in parentheses are in millimeters unless otherwise specified. 10 Planning Information Integrated Model 700 BF (I ) TOE KICK CLEARANCE The toe kick clearance can vary with the height of the lower drawer panel; the maximum panel height is 16 11/16" (424). IMPORTANT NOTE: You must keep a minimum space of 4" (102) clear below the bottom edge of the lower drawer panel so the unit can be properly vented. In addition, any decorative base molding must be removable for possible servicing and cleaning of the condenser. [. . . ]