User manual SUB-ZERO BBQ INSTALL GUIDE

[. . . ] GAS BBQ GRILLS INSTALLATION INSTRUCTIONS As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equipment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation. WOLF ® is a registered trademark of Wolf Appliance Company, LLC WO L F GAS BBQ GRILLS I N S TA L L AT I O N R E Q U I R E M E N T S IMPORTANT NOTE: This installation must be completed by a qualified installer, service agency or gas supplier. IMPORTANT NOTE: Save these Installation Instructions for the local inspector's use. [. . . ] The radiants are supported on each end by a pin located just above the grill burner. Be sure the heat radiants are oriented so that the triangular cut-out is positioned to the rear of the grill. The Wolf BBQ grill design eliminates the use of briquettes or lava rocks. The grill burners produce 10, 000 Btu/hr (2. 9 kW) per burner. The battery-powered ignition uses a AAA battery, provided with the BBQ grill, to be installed behind each ignition button. To install or replace, remove the ignition button by unscrewing in a counterclockwise direction. Insert the AAA battery into the cavity with the positive end in first and replace the ignition button. To make sure the sparker is operating, press the ignition button and listen for a spark. Grill Grate Radiant Burner Insert battery behind ignition button BBQ grill components Dimensions in parentheses are in millimeters unless otherwise specified. Radiant positioning Location of battery 13 WO L F GAS BBQ GRILLS N AT U R A L G A S H O O K - U P LP GAS H O O K - U P For Wolf natural gas BBQ grill models, hook-up is made from the rear right side with the fittings and regulator shown. The coupling, pipe nipple, street elbow and regulator are provided. To hook up the fittings, refer to the illustrations below. Make sure the flow arrow on the regulator points in the direction of the gas flow from the gas supply to the BBQ grill. Wolf BBQ grills set up for use with LP gas come equipped with a 5' (1. 5 m) hose, regulator and an unfilled 20-pound LP gas cylinder. LP (liquefied petroleum) gas is sometimes called propane, butane or bottled gas. It is a flammable gas which becomes liquid when stored under high pressure inside a cylinder and it vaporizes when released. Leaking LP gas tends to collect in low areas and could cause a fire or explosion. It is important there are no leaking connections on your gas BBQ grill. Refer to the Gas Leak Testing on page 17. Manifold Pipe Regulator To Grill Vent Regulator Shut-Off Valve Adapter Close Nipple From Gas Supply Natural gas hook-up Natural gas regulator 14 I N S TA L L AT I O N I N S T R U C T I O N S LP GAS C Y L I N D E R C Y L I N D E R S P E C I F I C AT I O N S Any LP gas cylinder used with this BBQ grill must be approximately 12" (305) diameter and 18" (457) high. The maximum fuel capacity is 20 lbs (9. 1 kg) or 5 gallons (19 L). The full cylinder weight should be approximately 38 lbs (17. 2 kg), which is 43. 7 lbs (19. 8 kg) nominal water capacity. The LP gas cylinder must be provided with an approved overfilling preventive device (OPD). All LP gas cylinders used with this appliance must be constructed and marked in accordance with the specifications for LP gas cylinders. Always use the cylinder dust cap on the cylinder valve outlet during transport and when the cylinder is not connected to the BBQ grill. The LP gas cylinder provided with the grill is equipped with a quick connect closing (QCC-1) cylinder valve. The valve contains a backcheck which is designed to prevent gas flow until it is connected to the regulator. [. . . ] If you are unable to stop a leak, shut off the gas supply at the cylinder valve. Do not use the appliance until the leak is corrected. Push in and turn any control knob to the on position to release pressure in the hose and manifold. Turn OFF the control knob. Testing for gas leakage of the appliance shall be conducted according to the manufacturer's instructions. Do not store a spare LP gas cylinder under or near this appliance. [. . . ]