User manual SUB-ZERO GASRANGE INSTALL

[. . . ] GAS RANGES INSTALLATION INSTRUCTIONS C O N TA C T I N F O R M AT I O N Wolf Customer Service: 800-332-9513 Website: wolfappliance. com As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equipment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation. WOLF ® is a registered trademark of Wolf Appliance Company, Inc. WO L F GAS RANGES I N S TA L L AT I O N R E Q U I R E M E N T S IMPORTANT NOTE: This installation must be completed by a qualified installer, service agency or gas supplier. IMPORTANT NOTE: Save these Installation Instructions for the local inspector's use. [. . . ] 3) After removing the mounting screws, move the hinge retainer plate forward slightly. NOTE: The hinge retainer plate will remain on the door hinge assembly after the mounting screws have been removed. 4) Carefully close the oven door to about a 60° angle from horizontal and lift the door away from the oven. NOTE: A slight racking motion may be required for removal. 5) For 48" (1219) and 60" (1524) gas ranges, complete these steps for both oven doors. IMPORTANT NOTE: The oven door(s) should not be removed unless it is necessary to fit the range through a tight doorway. Door removal should only be done by a qualified service technician or installer. Door removal and reinstallation may cause damage to the porcelain interior of the oven or door(s). If removal of the oven door(s) is necessary, a hinge pin, supplied with the range, will need to be inserted in the appropriate hinge arm. For each oven door, only one hinge arm is spring loaded, requiring use of the hinge pin for removal of the oven door. The hinge pin will be found taped to the inside of the oven door. For 30" (762) and 36" (914) gas ranges, the hinge pin will be inserted through the hole in the right hinge arm (facing the unit). On 48" (1219) and 60" (1524) gas ranges, the spring hinges are located on the outer edges of the unit. On these units, the left oven door will have the spring hinge on the left side and the right oven door will have the spring hinge on the right side. Refer to the illustrations below for the location of the spring hinge(s) for your specific model. Do not lift or carry the oven door by the door handle. Hinge Retainer Plate Hinge Pin Upper Mounting Screw Place Hinge Pin on Spring Hinge Side of Door Place Hinge Pins on Spring Hinge Side of Door Kickplate Spring hinge location for 30" (762) and 36" (914) gas ranges 12 Spring hinge locations for 48" (1219) and 60" (1524) gas ranges Oven door removal I N S TA L L AT I O N I N S T R U C T I O N S LEVEL T H E R A N G E IMPORTANT NOTE: The top of the range must be level. Use both the adjustable front legs and the adjustable rear casters to level the range. The 3" (76) front legs are adjusted by rotating the bottom hexagonal portion of the leg. The rear casters can be adjusted by rotating the 2 5/16" (59) nut on the caster. The range legs and casters allow for a 1" (25) upward height adjustment. Using the supplied wrench, rotate the nut clockwise to raise the unit or counterclockwise to lower the unit. Refer to the illustration below. REAR CASTER ADJUSTMENT NUT HEIGHT ADJUSTMENT WITH SUPPLIED WRENCH Rear caster adjustment Dimensions in parentheses are in millimeters unless otherwise specified. 13 WO L F GAS RANGES G A S S U P P LY R E Q U I R E M E N T S G A S S U P P LY C O N N E C T I O N EXPLOSION HAZARD -- Use a certified gas supply line and install a gas shut-off valve. IMPORTANT NOTE: The gas range must be connected to a regulated gas supply. Connect the range to the gas supply line. The gas supply line must be of adequate size to properly service all gas appliances. [. . . ] Check that the burner parts are in the proper position. Check that the power supply cord is plugged in and that the circuit breaker or house fuse has not blown. Check that the shut-off valve is in the ON position. Check operation again, waiting at least five minutes; if the burners do not light properly at this point, contact a Wolf authorized service center. [. . . ]