User manual SUB-ZERO ICE MACHINE

[. . . ] U NDERCOUNTER I CE M ACHINE INSTALLATION & OPERATION CONTENTS Ice Machine Installation Installation Checklist Ice Machine Features Ice Machine Operation Ice Machine Care Troubleshooting Guide Service Information Sub-Zero Warranty 4 16 17 18 23 28 30 31 Features and specifications indicated herein and on the website are subject to change at any time without notice. Check our website, subzero. com, for the most up-to-date specifications. As you follow these instructions, you will notice WARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Sub-Zero equipment. There are two types of potential hazards that may occur during installation. signals a situation where minor injury or product damage may occur if you do not follow instructions. states a hazard that may cause serious injury or death if precautions are not followed. Another footnote we would like to identify is IMPORTANT NOTE: This highlights information that is especially relevant to a problemfree installation. SUB-ZERO ® is a registered trademark of Sub-Zero, Inc. S U B - Z E R O I C E M AC H I N E I N S T A L L A T I O N A N D O P E R AT I O N T H A N K YO U Congratulations on the purchase of your Sub-Zero ice machine. [. . . ] The pin must be inserted until the head has made contact with the hinge body. 3) Insert the stop pin into the top door hinge (pin enters from the bottom). H I N G E C O V E R I N S TA L L AT I O N Install the door panel by engaging the tabbed bracket to the door first and then sliding the hinge side hardware over the positioning screws. You will have a 1/4" inch adjustment, up and down, side to side, with this hardware. Once you have the door in place, attach the remaining #8 x 1/2" screws to the hinge side mounting bracket and install decorative caps. If the reveal on the hinge side of the door panel is less than 1/4", and the panel has a square corner, severe finger pinching or damage to the unit may occur. IMPORTANT NOTE: Install the hinge covers after installation of the ice machine is complete. The 90-degree door stop must be installed prior to installing the hinge covers. 1) Remove the backing paper of the adhesive pads and bond to the hinge. 2) Install center covers (magnets will secure these covers). IMPORTANT NOTE: Hinges must be free of dirt or grease before applying covers. IMPORTANT NOTE: It will be necessary to remove the knock-out in the hinge cover when the 90-degree door stop is used. Door Stop Pin Knock-Out 90-degree door stop Hinge cover installation Dimensions in parentheses are in millimeters unless otherwise specified. 15 S U B - Z E R O I C E M AC H I N E I N S TA L L AT I O N I N S TA L L AT I O N C H E C K L I S T IMPORTANT NOTE: To ensure a safe and proper installation, the following checklist should be completed by the installer to ensure that no part of the installation has been overlooked. C O N TA C T I N F O R M AT I O N Sub-Zero customer service: 800-222-7820 Website: subzero. com Has the ice machine been installed where the incoming water temperature will remain in the range of 50­80°F (10­27°C)?Is the ice machine drain line routed to an open site drain for gravity drains and per instructions for pump units?Has the owner/operator been instructed regarding maintenance and the use of cleaner and sanitizer?Has the ice machine and bin been sanitized?Have the water and drain connections been examined for leaks?NOTE: If air temperature is less than 60°F (16°C), water temperature must be equal to or greater than 50°F (10°C). Any questions or problems about the installation should be directed to your Sub-Zero dealer or Sub-Zero customer service at 800-222-7820. You can also visit our website at subzero. com. Check to see if the unit is operating before you install. If applicable, is the door panel installed properly?Have any installation or service problems been noted on the product registration card?Instruct the owner to register the product. Has all of the internal packing been removed? [. . . ] Model Number Serial Number Installation Date Sub-Zero Authorized Service Center and Phone P R O D U C T R E G I S T R AT I O N Register your new Sub-Zero today so that we may ensure your satisfaction. You may register by one of the following options: 1) Mail in the completed Sub-Zero product registration card. 3) Register by phone by calling the Sub-Zero customer service department at 800-222-7820. The model and serial numbers of your unit are printed on the enclosed Sub-Zero product registration card. [. . . ]