User manual SUB-ZERO INDUCTION INSTALL GUIDE

[. . . ] Record the model and serial numbers before installing the cooktop. Both numbers are on the model / serial rating plate, located on the underside of the cooktop. Model Number CT15I/S Serial Number Proper installation is your responsibility. Have a qualified technician install this cooktop. [. . . ] A grounded junction box needs to be placed within 4' (1. 2 m) of the right rear of the cooktop. IMPORTANT NOTE: A minimum height clearance of 6" (152) is required. If a shelf is installed below the unit, a 1" (25) gap at the rear of the cabinet shelf is necessary to allow for proper ventilation. Failure to do so could result in decreased performance or product damage. MODEL CT15I/S DIMENSIONS Overall Width Overall Height Overall Depth Minimum Cabinet Depth Minimum Height Clearance Cut-Out Width* Cut-Out Depth 15" (381) 2 1/2" (64) 21" (533) 22 3/4" (578) 6" (152) 13 3/8" (340) 19 1/4" (489) *If the induction cooktop is to be used with any combination of additional cooktops or modules with a filler strip, the cut-out width increases to 14" (356). 21" (533) OVERALL DEPTH 15" (381) OVERALL WIDTH 19 1/4" (489) COOKTOP CUT-OUT DEPTH 24" OR 30"* (610 or 762) TO COOKING SURFACE 18" (457) 33" (838) RECOMMENDED CABINET WIDTH 13 3/8" (340) CUT-OUT WIDTH 18" (457) 2 1/2" (64) 2 1/2"min (64) 2"** (51) 2"** (51) 6" Overall Dimensions 36" (914) STANDARD FLOOR TO COUNTER HEIGHT E (152) 15" (381) 15" (381) NOTE: Application shown allows for installation of two 15" (381) modules side-by-side. *Minimum 24" (610) from protected cabinet or 30" (762) from unprotected cabinet to cooking surface. **Minimum clearance from side edge of cooktop cut-out to combustible surface up to 18" (457) above cooking surface. Installation Specifications and Countertop Cut-Out Dimensions 13 3/8" (340) COOKTOP CUT-OUT WIDTH 19 1/4" (489) 2 1/2"min (64) COOKTOP CUT-OUT DEPTH Dimensions in parentheses are in millimeters unless otherwise specified. FRONT OF COUNTERTOP 5 W O L F I N D U C T I O N C O O K TO P I N S TA L L AT I O N S P E C I F I C A T I O N S C O U N T E R T O P C U T- O U T The induction cooktop is designed to fit a standard 24" (610) deep base cabinet with 25" (635) deep countertop. Before making the cooktop cut-out, verify that the cooktop will clear the side walls of the base cabinet below. There should be at least 5 1/2" (140) clearance between the top countertop surface and any combustible surface directly below the unit. This includes upper edges of drawers located directly below unit. IMPORTANT NOTE: When multiple cooktops and/or modules are installed side by side, refer to the illustration below for countertop cut-out dimensions. IMPORTANT NOTE: Plastic or other utensils with low melting temperatures should not be located in drawers directly below unit. M U LT I P L E C O O K T O P I N S T A L L AT I O N IMPORTANT NOTE: If the induction cooktop is to be used with any combination of additional cooktop units or modules with a filler strip, the cut-out width is calculated by adding the corresponding units' cut-out dimensions plus 1 1/4" (32) for each additional unit. If multiple modules are to be installed, the cutout width of the induction cooktop should be increased from 13 3/8" (340) to 14" (356). IMPORTANT NOTE: When multiple units are installed side by side, each unit must have its own separate recommended electrical circuit. IMPORTANT NOTE: When two or more modules are installed together, an integrated module filler strip (IFILLER/S) is required. If a downdraft ventilation system is also installed, an integrated module support for downdraft ventilation (ISUPPORT) is required. Contact your Wolf dealer for information on these accessory components. 593/4" (1518) FOUR MODULES WIDTH OR 591/2" (1511) 30" COOKTOP AND TWO MODULES OR 501/4" (1276) 36" COOKTOP AND ONE MODULE 441/2" (1130) THREE MODULES WIDTH OR 441/4" (1124) 30" COOKTOP AND ONE MODULE 291/4" (743) TWO MODULES WIDTH 14" 21/2"min (64) (356) CUT-OUT WIDTH 191/4" (489) CUT-OUT DEPTH FRONT OF COUNTERTOP Countertop cut-out dimensions for installation of multiple cooktops 6 I N S TA L L AT I O N I N S T R U C T I O N S V E N T I L AT I O N O P T I O N S IMPORTANT NOTE: It is recommended that you operate the Wolf induction cooktop with either a Wolf cooktop hood, downdraft system or Pro ventilation hood. Cooktop Wall Hood ­ 30" (762) or 36" (914) widths in classic stainless steel. Cooktop Island Hood ­ 42" (1067) width in classic stainless steel. Downdraft Ventilation System ­ 30" (762) or 36" (914) widths, with top cover and control panel in classic, platinum and carbon stainless steel finishes (adequate countertop depth is required). Pro Wall Hood ­ 22" (559), 24" (610) or 27" (686) depths and 30" (762) to 66" (1676) widths in classic stainless steel. Pro Island Hood ­ 36" (914) to 66" (1676) widths in classic stainless steel. Pro Hood Liner ­ available in widths to accommodate 30" (762) to 60" (1524) hood shells. All hoods have welded seams, sealed halogen lighting and removable dishwasher safe stainless steel filters. [. . . ] The cooktop must be disconnected from power prior to service. 10 Dimensions in parentheses are in millimeters unless otherwise specified. I N S TA L L AT I O N I N S T R U C T I O N S I F Y O U N E E D S E RV I C E Maintain the quality built into your induction cooktop by calling a Wolf Factory Authorized Service Center. To obtain the name and number of a Wolf Factory Authorized Service Center, call Wolf Customer Service at 800-332-9513 or check our website, wolfappliance. com. When calling for service, you will need the cooktop model and serial numbers. Both numbers are listed on the model / serial rating plate, located on the underside of the cooktop. C O N TA C T I N F O R M AT I O N Wolf Customer Service: 800-332-9513 Website: wolfappliance. com E-mail Address: customerservice@ wolfappliance. com The information and images are the copyright property of Wolf Appliance Company, LLC, an affiliate of Sub-Zero Freezer Company, Inc. [. . . ]