User manual SUB-ZERO STEAMER INSTALL GUIDE

[. . . ] Record the model and serial numbers before installing the steamer module. Both numbers are listed on the product rating plate located on the underside of the module. Refer to the illustration below. IMPORTANT NOTE: Installation and service must be performed by a qualified installer or service agency. Warranty service must be performed by a Wolf authorized service center. [. . . ] *Minimum clearance from both side edges of cooktop cut-out to combustible materials up to 18" (457) above countertop. **Minimum clearance from rear edge of cooktop cut-out to combustible materials up to 18" (457) above countertop. 14" (356) COOKTOP CUT-OUT Installation Specifications WIDTH Countertop Cut-Out Dimensions 19 1/4" (489) 2 1/2" min (64) COOKTOP CUT-OUT DEPTH Dimensions in parentheses are in millimeters unless otherwise specified. FRONT OF COUNTERTOP 5 WO L F STEAMER MODULE I N S TA L L AT I O N S P E C I F I C A T I O N S DRAIN CONNECTION IMPORTANT NOTE: The steamer module must be installed with a drain connection and access to the drain through the base cabinet. For the drain connection, the 5/8" (16) outlet from the valve will accept a drain hose that must flow downward to and tie into an existing sink drain, or a separate drain with a freefall may be installed. Following local building codes, your plumber will dictate how to plumb the unit. As a third option, the consumer will supply a heat resistant bucket for drainage in the location of the drain outlet. Refer to the illustration on page 5 for location of the drain outlet. M U LT I P L E C O O K T O P I N S T A L L AT I O N IMPORTANT NOTE: If the steamer module is to be used with a combination of additional cooktop units or modules with a filler strip, the cut-out width is calculated by adding the corresponding units' cut-out dimensions plus 1 1/4" (32) for each additional unit. When multiple units are installed side by side, each unit must have its own separate recommended electrical circuit. When two or more modules are installed together, an integrated module filler strip (IFILLER/S) is recommended. If a downdraft system is also installed, an integrated module support for downdraft ventilation (ISUPPORT) is required (Model DD30 only). Contact your Wolf dealer for information on accessories. IMPORTANT NOTE: Review specific installation instructions for product to product capabilities. If there is no fixed drain connection, use a heat-resistant receptacle with a minimum 2 1/2-gallon (7. 6 L) capacity. The doors of the base cabinet must be locked. This steamer module must be installed at least 15" (381) away from a Wolf fryer module, as contact between water and hot oil may cause burns from steam and hot oil. 593/4" (1518) FOUR MODULES WIDTH OR 591/2" (1511) 30" COOKTOP AND TWO MODULES OR 501/4" (1276) 36" COOKTOP AND ONE MODULE 441/2" (1130) THREE MODULES WIDTH OR 441/4" (1124) 30" COOKTOP AND ONE MODULE 291/4" (743) TWO MODULES WIDTH 14" 21/2"min (64) (356) CUT-OUT WIDTH 191/4" (489) CUT-OUT DEPTH FRONT OF COUNTERTOP Countertop cut-out dimensions for installation of multiple cooktops 6 I N S TA L L AT I O N I N S T R U C T I O N S V E N T I L AT I O N O P T I O N S IMPORTANT NOTE: It is recommended that you operate the Wolf electric steamer module with either a Wolf cooktop or Pro ventilation hood or hood liner. Cooktop Wall Hood ­ 30" (762) or 36" (914) widths in classic stainless steel. Cooktop Island Hood ­ 42" (1067) width in classic stainless steel. Pro Wall Hood ­ 22" (559), 24" (610) or 27" (686) depths and 30" (762) to 66" (1676) widths in classic stainless steel. Pro Island Hood ­ 36" (914) to 66" (1676) widths in classic stainless steel. Pro Hood Liner ­ available in widths to accommodate 30" (762) to 60" (1524) hoods. All hoods have welded seams, sealed halogen lighting and removable, dishwasher-safe filters. IMPORTANT NOTE: Wolf does not recommend the use of downdraft ventilation with the steamer module. IMPORTANT NOTE: When installing a ventilation hood, refer to the specific requirements of the hood for the minimum dimension to the countertop. ACCESSORIES Optional accessories are available through your Wolf dealer. [. . . ] To obtain the name and number of a Wolf authorized service center, check the Locator section of our website, wolfappliance. com or call Wolf Customer Service at 800-332-9513. When calling for service, refer to the model and serial number of the steamer module. Both numbers are listed on the product rating plate located on the underside of the module. IMPORTANT NOTE: Installation and service must be performed by a qualified installer or service agency. [. . . ]