User manual SUPERMICRO X9DRD-EF

[. . . ] X9DRD-iF X9DRD-LF USER’S MANUAL Revision 1. 1a The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our website at www. supermicro. com. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice. [. . . ] BMC LED LED3 LEDM1 JIPMB1 BMC CTRL LAN CTRL BMC FAN8 JPG1 JPB1 FAN7 LAN2 LAN1 IPMI_LAN SP1 LAN CTRL JD1 JI2C1 JI2C2 CLK CTRL JPL1 JVRM_I2C1 JVRM_I2C2 JTPM1 CPU1 SLOT3 PCI-E 3. 0 X8 CPU1 SLOT5 PCI-E 3. 0 X8 PCH CPU1 SLOT4 PCI-E 3. 0 X8 CPU2 SLOT6 PCI-E 3. 0 X16 CPU2 SLOT7 PCI-E 3. 0 X8 JBT1 X9DRD-iF Rev. 1. 10 G1 H1 F1 JPW4 E1 CPU2 JPME2 JPME1 JWD1 JSD1 BIOS JRK1 I-SATA0 I-SATA2 I-SATA4 SCU0 SCU2 USB4/5 USB8/9 T-SGPIO1JSTBY1 JL1 FAN6 I-SATA1 C1 D1 B1 A1 I-SATA3 I-SATA5 SCU1 SCU3 T-SGPIO2 S-SGPIO1 CPU1 JVR2 JPW3 JBAT1 JPW1 A LED2 + JOH1 JPW2 :OH LED JPW5 FAN4 JVR1 FP CTRL JPI2C1 FAN1 FAN5 FAN2 FAN3 JF1 2-41 X9DRD-iF/LF Motherboard User’s Manual 2-10 SATA/SCU Connections SATA Ports/SCU Connectors There are four SATA 2. 0 Ports (SATA0~SATA3) and two SATA 3. 0 located on the X9DRD-iF. In addition, four SCU Connectors (SCU0~3) are also located on the board. These ports provide serial-link signal connections, which are faster than the connections of Parallel ATA. See the table on the right for pin definitions. Serial ATA/SCU Pin Definitions Pin# 1 2 3 4 5 6 7 Definition Ground TX_P TX_N Ground RX_N RX_P Ground Note 1: X9DRD-LF only has I-SATA0 and I-SATA1. Note 2: For more information on SATA HostRAID configuration, please refer to the Intel SATA HostRAID User's Guide posted on our website @ http://www. supermicro. com. . A. I-SATA0 COM1 USB6 COM2 JUIDB USB2/3 VGA USB0/1 LED3 LEDM1 BMC CTRL LAN CTRL B. SCU3 JIPMB1 BMC FAN8 JPG1 JPB1 FAN7 LAN2 LAN1 IPMI_LAN SP1 LAN CTRL JD1 JI2C1 JI2C2 CLK CTRL JPL1 JVRM_I2C1 JVRM_I2C2 JTPM1 CPU1 SLOT3 PCI-E 3. 0 X8 CPU1 SLOT5 PCI-E 3. 0 X8 PCH CPU1 SLOT4 PCI-E 3. 0 X8 CPU2 SLOT6 PCI-E 3. 0 X16 CPU2 SLOT7 PCI-E 3. 0 X8 JBT1 X9DRD-iF Rev. 1. 10 G1 H1 F1 JPW4 E1 CPU2 JPME2 JPME1 JWD1 JSD1 JRK1 A B C1 D1 BIOS B1 A1 I-SATA0 I-SATA2 I-SATA4 SCU0 SCU2 USB4/5 USB8/9 T-SGPIO1JSTBY1 JL1 FAN6 I-SATA1 I-SATA3 C E D F CPU1 I-SATA5 G H JVR2 SCU1 I J SCU3 T-SGPIO2 S-SGPIO1 JPW3 JBAT1 JOH1 + JPW1 JPW2 :OH LED LED2 JPW5 FAN4 JVR1 FP CTRL JPI2C1 FAN1 FAN5 FAN2 FAN3 JF1 2-42 Chapter 3: Troubleshooting Chapter 3 Troubleshooting 3-1 Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter. Note: Always disconnect the power cord before adding, changing or installing any hardware components. Before Power On 1. Make sure that there are no short circuits between the motherboard and chassis. 2. Disconnect all ribbon/wire cables from the motherboard, including those for the keyboard and mouse. 4. Install CPU 1 first (making sure it is fully seated) and connect the front panel connectors to the motherboard. No Power 1. Make sure that no short circuits between the motherboard and the chassis. 2. Make sure that the ATX power connectors are properly connected 3. Check that the 115V/230V switch on the power supply is properly set, if available. 4. Turn the power switch on and off to test the system, if applicable. 5. The battery on your motherboard may be old. Check to verify that it still supplies ~3VDC. If it does not, replace it with a new one. 3-1 X9DRD-iF/LF Motherboard User’s Manual No Video 1. If the power is on, but you have no video, remove all the add-on cards and cables. 2. Use the speaker to determine if any beep codes exist. Refer to Appendix A for details on beep codes. System Boot Failure If the system does not display POST or does not respond after the power is turned on, check the following: 1. Check for any error beep from the motherboard speaker. • there is no error beep, try to turn on the system without DIMM modules inIf stalled. If there is still no error beep, try to turn on the system again with only one processor installed in CPU Socket#1. If there is still no error beep, replace the motherboard. • there are error beeps, clear the CMOS settings by unplugging the power If cord and contracting both pads on the CMOS Clear Jumper (JBT1). [. . . ] Download this file to create a CD/DVD of the drivers and utilities it contains. (You may also use a utility to extract the ISO file if preferred. ) Another option is to go to the Supermicro Website at http://www. supermicro. com/ products/. Find the product page for your motherboard here, where you may download individual drivers and utilities. After creating a CD/DVD with the ISO files, insert the disk into the CD/DVD drive on your system and the display shown below should appear. Driver/Tool Installation Display Screen Note 1: Click the icons showing a hand writing on paper to view the readme files for each item. [. . . ]