User manual SWISHER 2645 CORRUGATED PLOW BLADE

[. . . ] Should you have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the name of the authorized Swisher dealer from whom you purchased the product will be needed before any warranty claim can be processed. THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last, so the above limitations or exclusions may not apply to you. [. . . ] Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. Never make adjustments or repairs with the engine running. · · 4 ASSEMBLY, INSTALLATION and PARTS LIST 5 TO ENSURE PROPER ASSEMBLY, CAREFULLY FOLLOW ALL INSTRUCTIONS LISTED BELOW REFER TO FIGURES 1 AND 2 WHILE ASSEMBLING THIS PORTION OF THE PLOW ATTACHMENT 1. Unpack parts and make sure all are included. If they are not contact the dealer where the Swisher Plow was purchased. Locate the pivot weldment (1) and assemble to the blade (2) using two ½-13 X 2" bolts (12) two ½-13 nyloc nuts (13) and two bushing (18) as shown. It is important to assure these two bushings are installed between the blade and pivot to allow for the correct rotation of the pivot. Assemble the tilt blocks (3) to the pivot weldment using two ½-13 X 2" bolts (12) and two ½-13 nyloc nuts (13). Assemble two 3/8-16 nuts (14 ) to two eye-bolts (6). Assemble the eye-bolts into the holes at the top of the blade. Secure with two 3/8 washers (15 ) two 3/8 -16 nuts (7). Place plastic caps (17) over the remaining threads of the eye-bolts. Attach the tilt springs (16) to the eye-bolts and to the tabs on the pivot weldment (1). Connect the skids (5) through the channels on the outer edges of the blade. Adjust their height with clevis pin (10) and hair pin (11). 6. 1 5 Tilt Blocks set the vertical "tilt" or rake of the blade Figure 1 6 PLOW ATTACHMENT ASSEMBLY FIGURE 2 7 14 6 16 8 12 4 18 9 11 10 12 5 18 13 26 13 19 28 20 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 QTY. 1 1 2 1 2 2 4 9 9 2 2 4 6 2 2 2 PART NO. 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 QTY 2 8 1 1 2 1 1 1 4 1 1 2 1 2 1 1 17 15 2 13 3 1 7 13 22 28 21 See detail on Page 8 21 27 30 PART NO. DESCRIPTION 2323TK Pivot Weldment 2312TK 50" Blade Weldment 2331TK Tilt Block 2317TK Cut Edge 2334TK Skid NB-635 3/8-16 X 3 Turned Eye Bolt NB-182 3/8-16 Nyloc Nut 10216 5/16-18 X 3/4 Carriage Bolt AS-125 Round Vinyl Cap NB-177 1/2 NR Mach. Bushing 2588TK Plow Mount 2642TK Plow Mount Pin NB-506 3/16 Click Pin 2327TK Plow Mount Bracket TR150W Washer 2336 Pivot Spring NB-170 5/16-18 Serrated Flange Nut NB-300 Clevis Pin Std ZP 3/8 NB-127 #3 Hair Pin NB-509 1/2-13 X 2 Hex Bolt NB-281 1/2-13 Nyloc Nut NB-212 3/8-16 Hex Nut NB-272 3/8 SAE Washer 2335 Tilt Spring NB-121 1/2-13 2 Way Jam Lock Nut NB-131 1/2-13 X 3 Hex Bolt 2310TK Plow Bracket Support NB-577 1/2-13 X 3 1/2 Hex Bolt 2319TK Lock Arm NB-649 3/8-16 X 3 1/2 Hex Bolt H9B H7K Rope (Not Shown) Knob (Not Shown) 7 TO ENSURE PROPER ASSEMBLY AND INSTALLATION, CAREFULLY FOLLOW ALL INSTRUCTIONS LISTED BELOW REFER TO FIGURES 2 AND 3 WHILE ASSEMBLING AND INSTALLING THIS PORTION OF THE PLOW ATTACHMENT The next steps need to be done in sequence: 1. Disassemble Pivot Latch assembly from the plow mount. [. . . ] 18 25 22 28 19 29 29 23 Tail of Spring 24 Top of weldment is removed for clarity. 24 1 8 Figure 3 ADJUSTMENT AND OPERATION PUSH YOUR PLOW AROUND!! THE TENSION PLACED ON THE TILT SPRINGS DETERMINE THE AMOUNT OF PRESSURE THAT MUST BE APPLIED TO THE BLADE BEFORE IT FOLDS OVER IF SOMETHING IS HIT. ADJUST THE SPRINGS BY LOOSENING THE NUTS (7) ON THE EYEBOLTS (6) AND ADJUSTING UNTIL THE BLADE DOES NOT FOLD OVER DURING NORMAL OPERATION BUT WILL FOLD IF AN OBJECT IS STRUCK. AFTER INSTALLING YOUR PLOW, SECURE THE ROPE SO IT IS ACCESSABLE WHILE OPERATING THE ATV AND SECURELY HELD. [. . . ]