User manual SWISHER 2646 UNIVERSAL MOUNTING KIT

[. . . ] Should you have any questions concerning this warranty, please contact us toll-free at 1-800222-8183. The model number, serial number, date of purchase, and the name of the authorized Swisher dealer from whom you purchased the mower will be needed before any warranty claim can be processed. THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last, so the above limitations or exclusions may not apply to you. [. . . ] Never make adjustments or repairs with the ATV engine running. OD55 Danger Decal OD45 Warning Decal - 3 15 or 16 24 25 1 8 7 19 18 9 12 2 26 22 17 23 28 4 14 3 13 Note: Accessory Mount Holes 28 9 27 5 21 20 11 FIGURE 1 10 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. 15 16 17 18 19 20 21 22 23 24 25 26 27 28 6 QTY. 1 1 2 2 2 1 1 2 8 2 2 4 2 2 DESCRIPTION QTY 1 1 1 2 2 2 2 2 4 1 1 2 4 8 PART NO. DESCRIPTION 2630TK Channel Mount 2593TK Slide Bar 2596TK Leaf Spring 2631TK Spring Shackle 2596-1 Nylon Bushing 2638TK ATV Bracket Left 2637TK ATV Bracket Right 2641TK Backing Bracket R&L NB-182 3/8 -16 Nyloc Nut NB-561 5/8 - 11 Nyloc Nut NB-699 5/8 - 11 X 3 GR 5 Hex Bolt NB-645 3/8 - 16 x 4 GR 5 Hex Head NB-247 Hair Pin #10 NB-244 1/2 X 2 3/4 Clevis Pin NB-655 3/4 - 10 X 7 1/2 GR 5 Bolt NB243 3/4 - 10 X 5 GR 5 Bolt NB-609 3/4 - 10 Nyloc Nut 2633TK Mount Bracket Short 2635TK Bracket Plate Short 2632TK Mount Bracket Long 2634TK Bracket Plate Long NB-281 1/2 - 13 Nyloc Nut NB-177 1/2 NR Mach Bushing 9609TK Spacer 1. 25 X . 75 X 2. 1875 2655TK Spacer 1. 25 X . 75 X 1. 5 NB-577 1/2 - 13 X 3 1/2 GR5 Bolt NB-619 3/8 - 16 X 2 1/2 GR5 Bolt NB-272 3/8 SAE Washer 4 INSTALLATION OF ACCESSORY MOUNT TO ENSURE PROPER INSTALLATION, CAREFULLY FOLLOW ALL INSTRUCTIONS LISTED BELOW MOUNTING BRACKETS Included with your new ATV accessories mount are three sets of mounting brackets for ATV's. Brackets 18, 19 and 20, 21 are two sets that will work on most ATV's. The determining factor is what type of A-arms (lower portion of the front axle) are used on your ATV. If your A-arm is narrow then use bracket set 18, 19. If your A-arm is wide then use bracket set 20, 21. If you have a Polaris ATV use brackets 6, 7, and 8. Note: The Polaris brackets are right and left oriented. Make sure you set them up as shown in Fig. 1. REFER TO FIGURE 1 WHILE INSTALLING THE ACCESSORY MOUNT NOTE: The CV guards on your ATV maybe need to be trimmed or otherwise modified to allow for installation and proper clearance for the Accessory Mount. If needed, for clearance, raise the front of the ATV. Make sure the support used is very stable. Lay out the hardware under the ATV, as shown. Mount the proper brackets to the lower A-arms of your ATV as near as possible to the outside end. Mount leaf springs (3) to mounting brackets with clevis pin (14) and hair pin (13). Attach channel mount (1) to the ATV ball hitch mount with 3/4 - 10 bolt (15 OR 16) and 3/4 - 10 nyloc nut (18). Note: the spacers (24 and 25) need to be installed to keep the accessories mount assembly level and for clearance. Using two 1/2 - 13 bolts (26), four 1/2 bushings (23) and two 1/2 - 13 nyloc nuts (22) attach slide bar (2) to channel mount (1). If previously raised, lower the ATV to the ground. Place the two leaf springs (3), from step 4 and the assembly from step 6 between the spring shackles (4). [. . . ] Front bolt NB619 should be close to the front of the A-arm, contacting it if possible. Bracket Plate Long #2634TK Honda A-arm U-bracket #2677TK Mount Bracket Long #2632TK 3/8 ­ 16 bolt #NB-619 3/8 ­ 16 Nyloc Nut #NB182 Bombardier Traxter Mounting Instructions Notched Plate (Part # 7120) INSTALLATION INSTRUCTIONS Kit # 7119 Required Same as above with addition of spacer and guard modification Spacer (Part # 7121) Bracket A Arm Guard Modification Guard to be modified by Owner 6 Bombardier Outlander Accessory Mount Brackets Kit #7668 3/8 NYLOC NUT HARDWARE AND PARTS 2 - ACCESSORY MOUNT BRACKET 2 - ACCESSORY MOUNT WELDMENT 4 - 3/8-16 X 2 ½ BOLT 8 - 3/8 SAE WASHER 4 - 3/8 - 16 NYLOC NUT 2 - 5/16 - 18 X 2 BOLT 2 - 5/16 -18 NYLOC NUT 4 - 5/16 SAE WASHER 5/16 NYLOC NUT 7669TK 7670TK NB619 NB272 NB182 NB507 NB181 NB275 5/16 SAE WASHER ACCESSORY MOUNT BRACKET 3/8 X 2 ½ BOLT ACCESSORY MOUNT WELDMENT MOUNTING INSTRUCTIONS 5/16 X 2 BOLT 3/8 SAE WASHER (REFERENCE FIGURE ABOVE, LEFT SIDE SHOWN) RAISE ATV SO THERE IS ENOUGH ROOM TO WORK. MAKE SURE THE SUPPORT USED TO HOLD UP THE ATV IS VERY STABLE. LAY OUT THE PARTS AND HARDWARE UNDER THE ATV. MOUNT THE BRACKET AND WELDMENT AS SHOWN IN THE FIGURE. [. . . ]