User manual SWISHER FC-10 DUMP CART

[. . . ] THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of consequential damages or limitations on how long an implied warranty may last, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights, which vary from state-to-state. [. . . ] Next, finish bolting together two middle connections of Bottom Panels after Wheel Axle Support is in place. Using 2 (#21) Bolts, 2 (#23) Washers, and 2 (#24) Nuts. Hardware Needed for Step 5: 2 (#4) Wheel Axle Supports (connected) 10 (#21) Bolts 10 (#23) Washers 10 (#24) Nuts Step 6: Attaching Wheel Axle and Tires Set Hitch Tongue(#10) in place as shown below before inserting Wheel Axle(#5) through Wheel Axle Support(#4). Next, insert the Wheel Axle (#5) into the Wheel Axle Support(#4), and through the holes in the Tongue(#10) as shown in Figure 6. Be sure equal amounts of axle extend from each side of Wheel Support. Next, install each Tire Assembly (#6) onto Wheel Axle, followed by a Washer(#26) and a Cotter Pin(#27) Hardware Needed for Step 6: 1 (#10) Hitch Tongue 1 (#5) Wheel Axle 2 (#6) Wheel Assemblies (Tires) 2 (#26) Washers 2 (#27) Cotter Pins Step 7: Assembling Tongue Latch Insert the Tongue Latch(#9) up through the opening in the Hitch Tongue(#10). Place one Latch Spacer(#8) on each side of the Tongue Latch(#9), the insert Bolt(#29) to connect Hitch Tongue(#10) and Latch Spacers(#8) and Tongue Latch(#9). Only Hand Tighten (#29) Bolt to (#30) Nut. Next, attach one end of Latch Spring(#7) to Hitch Tongue(#10) and one end of Latch Spring(#7) to top hole in Tongue Latch(#9). Now completely tighten (#29) Bolt and (#30) Nut. Hardware Needed for Step 7: 1 (#9) Tongue Latch 2 (#8) Latch Spacers 1 (#7) Latch Spring 1 (#29) Bolt 1 (#30) Nut Page 7 Step 8: Installing the Hitch Pin Bracket Install the Hitch Pin Bracket(#11) in the back two holes of the Hitch Tongue(#10) using 2 (#25) Bolts, 2 (#23) Washers, and 2(#24) Nuts. Place Hitch Pin(#28) in the front hole, using Cotter Pin(#27) to hold in place. Hardware Needed for Step 8: 1 (#11) Hitch Pin Bracket 2 (#25) Bolts 2 (#23) Washers 2 (#24) Nuts 1 (#28) Hitch Pin 1 (#27) Cotter Pin Step 9: Installing the Rear Cross Brace Turn the Trailer Cart over onto its wheels. Attach the Rear Corner Brackets(#13) and the Rear Cross Brace(#12) to the back of the Bottom Panels as shown in Figure 9. Use 2 (#21) Bolts, 2 (#23)Washers, and 2 (#24) Nuts for each side. Hardware Needed for Step 9: 1 (#12) Rear Cross Brace 2 (#13) Corner Brackets 4 (#21) Bolts 4 (#23) Washers 4 (#24) Nuts Step 10: Side Panel Installation Attach the Left Side Panel(#14) to the Bottom Panels as shown in Figure 10 using 2 (#21) Bolts, 2 (#23) Washers, and 2 (#24) Nuts. Hardware Needed for Step 10: 1 (#14) Side Panel 2 (#21) Bolts 2 (#23) Washers 2 (#24) Nuts Page 8 Step 11: Secure Rear Cross Brace Bolt Rear Cross Brace(#12) to Bottom Panels(#1) using 6 (#21) Bolts, 6 (#23) Washers, and 6 (#24) Nuts. Hardware Needed for Step 11: 6 (#21) Bolts 6 (#23) Washers 6 (#24) Nuts Step 12: Side Panel Installation Attach the Right Side Panel(#14) to the Bottom Panels as shown in Figure 12 using 2 (#21) Bolts, 2 (#23) Washers, and 2 (#24) Nuts. [. . . ] Before using the cart, check that all hardware connections are tight. Hardware Needed for Step 16: 1 (#20) Tailgate 2 (#18) Tailgate Latches 2 (#19) Tailgate Pins 2 (#32) Washers 2 (#31) Nuts 4 (#21) Bolts 4 (#23) Washers 4 (#24) Nuts Page 10 Operation/Maintenance NOTES: Operation notesA full capacity load is 500 pounds, DO NOT exceed rated capacity. Cart only to be used with lawn tractor or ATV. [. . . ]