Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SWISHER GC-07 GARDEN CART. We hope that this SWISHER GC-07 GARDEN CART user guide will be useful to you.
Lastmanuals help download the user guide SWISHER GC-07 GARDEN CART.
Manual abstract: user guide SWISHER GC-07 GARDEN CART
Detailed instructions for use are in the User's Guide.
[. . . ] Line up three holes in bottom panel with holes in front angle assembly. Start three M6X25 screws through bottom panel, then through angle. Secure screws with 6 flat washers and M6 hex nuts. See figure 2.
Contents of Hardware Pack: (See figure 1)
REF. [. . . ] See figure 6.
FRONT ANGLE ASS'Y
FRONT PANEL
LARGE FLAT WASHER
FIGURE 4
2
FIGURE 6
10. Place one side panel in position against a side angle and down on top of the front panel. Start one M6X25 screw through the center hole in side panel and side angle. Start one M6X25 screw through front hole on side panel and side angle. Start another M6X25 screw through top hole on side panel and front angle assembly. Next, place a support strap over these two screws and secure it with flat washers and hex nuts. Repeat steps 10 and 11 for the other side panel.
6 FLAT WASHER
M6 HEX NUT M6X25 SCREW
13. Assemble one M6X25 screw through bottom hole in side panel and front angle assembly. Secure with a flat washer and hex nut, Only finger tighten at this time. Securely Tighten all loose nuts and screws at this time.
M6X25 SCREW SIDE PANEL FRONT PANEL
M6X25 SCREW
M6 HEX NUT
6 FLAT WASHER
FRONT ANGLE ASS'Y
SIDE PANEL
M6X25 SCREW
FIGURE 8
M6 HEX NUT
6 FLAT WASHER
FRONT ANGLE ASS'Y
FRONT PANEL
SUPPORT STRAP
FIGURE 7
3
15. Lay the cart down on the floor so that the sides are in an upright position. Remove the front panel by sliding it up, then remove the four large washers you used for shims. See figure 9.
SIDE PANEL (4) LARGE FLAT WASHERS USED AS SHIMS CART SIDE PANEL FRONT PANEL
17. Leave the cart standing to assemble the handle tube in the next step. Place tube caps on the handle tube, then place it over the side panels and line up the four holes. Assemble four M6X50 screws through the side panels and handle. See figure 11.
LEG TUBE
HANDLE TUBE
M6X50 SCREW M6 HEX NUT
FIGURE 9
16. Place tube caps on leg tube and assemble the leg tube as shown in figure 10, using four M6X50 screws through side panels and leg tube. See figure 10.
6 FLAT WASHER
FIGURE 11
19. See figure 12.
LEG TUBE
AXLE CLAMPS
M6 x50 SCREW
AXLE
6 FLAT WASHER
M6 HEX NUT TUBE CAP SIDE PANEL
FIGURE 10 FIGURE 12
4
20. [. . . ] Apply a light coat of varnish to all wood surfaces annually. Use glossy black enamel spray paint to touch up scratched or worn painted metal surfaces.
LARGE FLAT WASHER
RECOMMENDED TIRE PRESSURE 45-50 PSI MAXIMUM TIRE PRESSURE 50 PSI (350KPa)
FIGURE 13
22. Turn cart right side up, so that it rests on its wheels. Place front panel in guides to complete assembly. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SWISHER GC-07 GARDEN CART
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SWISHER GC-07 GARDEN CART will begin.
