User manual SWISHER GC-14 GARDEN CART

[. . . ] Contents of Hardware Pack: (See figure 1) REF. DESCRIPTION A 6 Screws, M6X50 B 2 Screws, M6X40 C 8 Screws, M6X30 D 21 Screws, M6X25 E 4 Cotter Pins F 37 Hex Nuts, M6 G 33 Flat Washer, 6 H 4 Lock Washer, 6 I 4 Large Flat Washer TOOLS REQUIRED (1) Screw Driver (1) Pliers (1)10mm Wrench When assembling your cart, place the heads of all screws to the inside and hex nuts with flat washers to the outside. Lay the front angle assembly down (flat) on floor and stand the bottom panel in position as shown in figure 2. NOTE The bottom panel has one galvanized edge; this is the rear. Line up three holes in bottom panel with holes in front angle assembly. [. . . ] Place a support strap on the outside of the side angle and start a M6X30 screw through the second hole in the side panel, the side angle and the support strap. Start a M6X30 screw through the top hole in the side panel. the front angle assembly and the support strap. Repeat steps 9 and 10 for the other side panel. SIDE ANGLE FRONT HOLE M6X25 SCREW SIDE PANEL FRONT PANEL BOTTOM HOLE M6 HEX NUT 6 FLAT WASHER FRONT ANGLE ASSEMBLY 6 FLAT WASHER M6 HEX NUT SIDE ANGLE SECOND HOLE FRONT HOLE M6X25 SCREW M6X30 SCREW FIGURE 8 15. Lay the cart down the floor so that the sides are in the normal upright position. remove the front panel by sliding it up, then remove the four large washers you used for shims. See figure 9. SIDE PANEL FRONT PANEL FRONT ANGLE ASS'Y SIDE PANEL M6X30 SCREW SUPPORT STRAP M6 HEX NUT 6 FLAT WASHER Top Hole SUPPORT STRAP (4) LARGE FLAT WASHERS USED AS SHIMS CART SIDE PANEL FRONT PANEL FIGURE 7 12. Start one M6X25 screw through the bottom hole in the side panel and the front angle assembly. Start another M6X25 screw through the front hole in the side panel and the side angle. Secure with two flat washers and two hex nuts, making only finger tight at this time. Repeat step 12 for the other side panel. Tighten all nuts and screws securely at this time, except for nuts and screws in axle clamps. Place the handle tube on the bottom of the cart as shown in figure 10. Place the four tube clamps over the handle tube, with the longer leg of each tube clamp to the outside. Secure the four tube clamps over the handle tube using eight M6X25 screws, eight flat washers and eight hex nuts. Make only finger tight until all eight screws are in place and then tighten securely. Insert a M6X25 screw through the hole at the rear of each side panel and the hole at the rear of each side angle. Secure with 6 flat washers and M6 hex nuts, making only finger tight at this time. Place the tube caps on the ends of the "W" shaped leg tube. With the cart still upside down, assemble the leg tube to the bottom of the cart. Line up the two holes in the center of the leg tube with the holes in the bottom of the cart. Secure the leg tube to the bottom of the cart with two M6X50 screws, 6 flat washers and M6 hex nuts. [. . . ] Periodically retighten all screws, especially after heavy use. Do not exceed load capacity rating of 400lbs. Apply light coat of varnish to all wood surfaces annually. Use glossy black enamel spray paint to touch up scratched or worn painted metal surfaces. RECOMMENDED TIRE PRESSURE 80-85 PSI MAXIMUM TIRE PRESSURE 85 PSI (600KPa) FIGURE 12 26. [. . . ]