User manual SWITEL WTC 605

[. . . ] Medical equipment Attention: Never use the walkie−talkies in the vicinity of medical equipment. effects on such equipment cannot be fully ruled out. Walkie−talkies can cause an unpleasant humming sound in hearing aids. 40 Safety Information Disposal In order to dispose of your device, take it to a collection point provided by your local public waste authorities (e. [. . . ] To detach the belt clip, prize the fastening tab away from the device a little with your fingernail and slide the belt clip upwards. 43 Operating Elements 3 Operating Elements The buttons in this operating manual are subsequently depicted with a uniform contour. Therefore, slight deviations in the appearance of the symbols on the walkie−talkie buttons compared to those depicted here are possible. Walkie−talkie 1 2 3 4 5 6 7 8 9 10 11 12 Display Decrease setting 10 On / Off Microphone Loudspeaker Transmit ringing tones 9 8 Menu button 7 Increase setting 6 PTT − Talk button Antenna Belt clip Headset/ Vehicle cigarette lighter charger cable socket 13 Battery compartment 1 2 3 4 5 11 12 13 Display 1 2 3 4 5 6 7 Transmitting Receiving Channel Volume control Key lock Battery capacity Channel scanning 7 6 1 2 3 5 4 44 Operating the Walkie−Talkies 4 Operating the Walkie−Talkies Display and notation of operating sequences P 3 sec. ¤ 2x¤ aP bP ð Press the button depicted Press the button depicted for 3 seconds Press the button depicted twice Press and hold the button depicted Release the button depicted Speak into the microphone Display illumination The display lights up for a few seconds after pressing a button. Switching the walkie−talkie on/off 23 aV Switch the walkie−talkie on An acoustic signal is issued. The current channel setting appears in the display. A V Switch the walkie−talkie off Volume control + or , Raise or lower the volume Transmitting and receiving Transmitting 24 aPð Transmit Hold the walkie−talkie approx. 5 to 7 cm from your mouth and speak at a normal volume. In order to talk to other subscribers, the respective walkie−talkies must be set to the same channel. Receiving 25 bP Receive Radio signals cannot be received when the P button is being pressed. 45 Operating the Walkie−Talkies Confirmation signal (Roger beep) The confirmation signal is issued on releasing the P button. This signals to the caller that you have ended transmission. 04375 Searching for a channel Signals are searched for in the eight channels in a continuous cycle. Starting channel scanning ¤ and + Start the channel search Resume the channel search Stop the channel search Resuming channel scanning + or , Stopping channel search P or ¤ Transmitting the ringing tone The ringing tones indicate to other subscribers that you want to talk to them. A condition for this is that the other subscribers are using the same channel. ‘ Transmit the ringing tone 46 Operating the Walkie−Talkies Monitor function The Monitor function enables the search for weak signals on the channel currently set. If you receive an external signal, switch to a free channel. Always communicate with other subscribers on a free channel to prevent interference. ¤ and , Start monitoring the channel ¤ End the monitoring function Key lock The key lock function prevents inadvertent modification of settings. When the key lock function is activated, the icon flashes in the display. ¤ Activate the key lock function Deactivate the key lock function Deactivating 27 3 sec. [. . . ] If your device does show signs of a defect within the period of guarantee, please contact the sales outlet where you purchased the SWITEL device, producing the purchase receipt as evidence. All claims under the terms of guarantee in accordance with this agreement can only be asserted at the sales outlet. No claims under the terms of guarantee can be asserted after a period of two years from the date of purchase and hand−over of the product. Important note Your device is supplied with an energy−efficient switching power supply (Input 230 VAC, Output 7. [. . . ]