User manual SYLVANIA 6260VB

[. . . ] · When a picture does not appear on the TV screen, repeat step 4). 5) Hit [STOP C] to stop playback. Hint · The RF output channel may not change when you adjust tracking during playback. In this case, stop the playback, and start the playback again. After that, hold [PLAY B] on the VCR for 3 seconds again. TOLL FREE : 1-800-968-3429 or visit our web site at http://www. SylvaniaConsumerElectronics. com 6260VB Basic TV Connection Cable TV Antenna Signal or 1. [. . . ] This reminder is provided to call the Grasp it by the plug. Cable TV system installer's attention to Article 820-40 of the NEC that provides Moisture Condensation Warning guidelines for proper grounding and in Moisture condensation may occur inside particular, specifies that the cable the unit when it is moved from a cold ground should be connected to the place to a warm place, or after heating a grounding system of the building, as cold room or under conditions of high close to the point of cable entry as poshumidity. CAUTION: FCC Warning TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO This equipment may generate or use WIDE SLOT, FULLY INSERT. Changes or ATTENTION: modifications to this equipment may POUR ÉVITER LES CHOCS cause harmful interference unless the modifications are expressly approved in ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA the instruction manual. The user could FICHE DANS LA BORNE CORRElose the authority to operate this equipment if an unauthorized change or modi- SPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. fication is made. Playback picture is partially noisy. · Adjust tracking control for a better picture by pressing [CHANNEL ]. · Head cleaning may be necessary. Refer to "Auto Head Cleaning" on page 8. · Make sure the VCR is not in the Menu mode. · Change the RF output channel to CH4. · Tracking will be automatically adjusted upon playback. To adjust the tracking manually, press [CHANNEL ]. Counter Reset Hit [C. RESET/EXIT]. 6. Recording & OTR (One Touch Recording) Before: Turn on the TV and set it to channel 3. · If channel 3 is already occupied for broadcasting, see "RF Output Channel" section. Hint · Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to the tape and the video head. · To return to playback from the Picture Search/Still/Slow mode, hit [PLAY B]. 2 6 EJECT VCR /TV 2 POWER 1 4 1 with tab 2 1 4 7 POWER VCR/TV Remote Control TV Screen 8. On-Screen Operations 1 To call up the main menu MENU 1 2 5 8 0 3 6 9 CHANNEL 2 5 8 0 SPEED 3 6 9 SLOW CHANNEL 4 CH12 7 MENU SEARCH -MODE C. RESET EXIT -MENUB TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP CLOCK SET LANGUAGE SELECT CHANNEL MENU REC/OTR STOP/EJECT REW PLAY F. FWD TAPE IN Select the channel to record. Select the desired tape speed. Recording/Playback Time T60 1hour 3hour T120 2hours 6hour REC POWER VCR/TV TAPE IN TIMER REC 3 SPEED SP Tape Speed Type of tape SP mode SLP mode 4 3 5 REC/OTR DISPLAY PAUSE /STILL REW STOP PLAY F. FWD 5 6 CHANNEL MENU REC/OTR STOP/EJECT REW PLAY F. FWD POWER VCR/TV TAPE IN TIMER REC 2 STOP To select an item PLAY T160 2-2/3hours 8hour -MENUTIMER PROGRAMMING AUTO REPEAT [OFF] B CHANNEL SET UP CLOCK SET LANGUAGE SELECT or 4 REC/OTR Accidental erasure prevention To prevent accidental recording on a recorded cassette, remove its record tab. To record on it later, cover the hole with adhesive tape. Record tab 1 4 POWER EJECT VCR/TV 23 REC Hit [REC/OTR] repeatedly to select the desired recording length. REC (Normal recording) OTR(8:00) OTR(0:30) OTR(1:00). . . . . OTR(7:30) 3 To decide F. FWD CHANNEL SET UP AUTO SET UP B MANUAL SET UP 1 4 7 2 5 8 0 SPEED 3 6 9 SLOW CHANNEL SEARCH -MODE C. RESET EXIT 5 STOP STOP 6 EJECT EJECT A Hint · If you have connected this unit to a cable box or satellite box, refer to "Hint for Cable Box or Satellite Box" section on page 1. 4 To exit the menu C. RESET EXIT 41 2 MENU REC/OTR DISPLAY PAUSE /STILL 4 3 EN MENU REW STOP PLAY F. FWD -5- or 9. Recording Features Timer Recording ·Insert a tape with its record tab into the unit. Hints for Timer Recording 1 MENU -MENUB TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP CLOCK SET LANGUAGE SELECT AUDIO OUT TV STEREO [ON] TIMER PROGRAMMING SAP PROG 12345678 DATE START TIME END TIME Available program CHANNEL 5 Select the desired start time (hour). STOP PLAY 9 STOP PLAY ONE TIME PROGRAM PROGRAM NUMBER 1 DATE 1 0 / 2 4 MON START TIME 0 7 : 3 0 PM END TIME 0 8 : 3 0 PM CHANNEL 16 REC SPEED SP B SP SLP ONE TIME PROGRAM PROGRAM NUMBER 1 DATE 10 / 2 4 MON START TIME 0 7 : 3 0 ­ ­ END TIME ­ ­ : ­ ­ ­ ­ CHANNEL ­­ REC SPEED ­ ­ or or F. FWD Select the desired recording speed. C. RESET EXIT number flashes. F. FWD Select the minute STOP PLAY · If there is a power failure or the unit has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost. · If the tape runs out before the end time, the unit will switch to the Stop mode immediately, eject the tape and the power will be turned off. · If a tape is not in the unit or does not have the record tab, the TIMER indicator flashes and timer recording cannot be performed. [. . . ] If a streaky or snowy picCabinet Cleaning ture appears during playback, the video heads in your VCR may need to be cleaned. · Wipe the front panel and other exterior surfaces of the VCR with a soft cloth immersed 1. Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner. · Never use a solvent or alcohol. [. . . ]