User manual SYMPHONIC CD10

[. . . ] 1) Connect the AUDIO/VIDEO output jacks of this DVD player to the AUDIO/VIDEO input jacks of your RF Modulator by audio and video cables. 2) The antenna input jack of your TV may have been already occupied. If so, disconnect the RF cable from your TV and then connect the RF cable to your RF Modulator (usually marked "ANT IN". ) 3) Connect your RF modulator to your TV by another RF cable. 4) Set your RF modulator's channel 3/4 switch to either 3 or 4, whichever the TV channel is least used in your area. [. . . ] · To advance playback one frame at a time. · To turn the unit on or off. · To pause disc playback. · To play a track or disc repeatedly. 2 REPEAT · To play a chapter or title repeatedly. · To return to the previous operation in the DVD setup menu. RETURN 3 SEARCH MODE · To search chapter, title or time. · To rapidly return to · To rapidly return to a location of disc. · To stop playback. Keep in mind the following when using the remote control: · Make sure that there is no obstacle between the remote control and the remote sensor on the unit. · Use within the operating range and angle, as shown. SETUP SKIP STOP SUBTITLE · To stop playback. · To call up the Top Menu on a disc. TOP MENU Remote control t ou ab 7m) in ( ith t W 3 fee 2 V. SURR. · To set virtual surround on/off. · To set virtual surround on/off. ­8­ EN Functions Operations described after this section are mainly based on the remote control use. Some operations can be carried out on the unit itself. Playback Before: Turn on the TV, amplifier and any other components which are connected to the DVD player. Make sure the TV and audio receiver (commercially available) are set to the correct channel. DVD-V CD OPEN/CLOSE OPEN/CLOSE PLAY STOP POWER 1 POWER 2 POWER SEARCH MODE OPEN/CLOSE 2 1341 5 Hint · A "prohibited icon" may appear at the top-right on the TV screen when the operation is prohibited by the disc or this unit. (Refer to pages 14-15) ­9­ EN Functions The On-Screen Display You can check the information about the current disc by pressing the DISPLAY button on the remote control. DVD-V DISPLAY CD DISPLAY Current playback status 11/16 0:00:00 - 0:03:30 Current playback status 4/12 0:03:21 - 0:02:15 Remaining time of the current track Remaining time of the current chapter Elapsed time of the current chapter DISPLAY Elapsed time of the current track TR(Track): Current track number / Total tracks ALL: Current track number / Total tracks Current repeat setting appears only when the repeat setting is active T : Track repeat A : All Tracks repeat A B : A-B repeat Remaining time of the current audio CD Elapsed time of the current audio CD DISPLAY CH (Chapter): Current chapter number / Total chapters 4/12 0:13:45 - 0:45:40 1/3 0:00:00 - 1:23:45 T Remaining time of the current title Elapsed time of the current title DISPLAY TT (Title): Current title number / Total titles DISPLAY T L1 Layer numbers, appears only when playing a two-layered Disc L0: Layer 0 is playing L1: Layer 1 is playing Current repeat setting appears only when the repeat setting is active C : Chapter repeat T : Title repeat A B:A-B repeat BIT RATE: The amount of audio and video data currently being read DISPLAY Functions ­ 10 ­ EN Search Function Track Search CD Title / Chapter Search DVD-V Time Search DVD-V CD Using the number buttons 1123 4 7 5 8 0 6 9 +10 /2 Using the SEARCH MODE button 1 SEARCH MODE 1 PLAY TOTAL 1:29:00 /12 SEARCH MODE ·For single digit tracks (1-9), press a single number (e. g. ·To play track 26, press +10, 2, 6 of the Number buttons. Press once for the chapter search Press twice for the title search Press repeatedly until this screen appears 2 5 8 0 3 6 9 TOTAL 1:29:00 2 1 4 2 1 4 7 2 5 8 0 3 7 6 9 +10 /12 Within 30 seconds Within 30 seconds · If the former digits of the total time are "0", "0" is entered automatically. if you enter 5:55, "0:0-:--" will be displayed on the time search screen. ) Using the SEARCH MODE button 1 SEARCH MODE /2 2 Using the SKIP H , G button 1 1 4 7 2 5 8 0 3 6 9 SKIP /2 PLAY Current Chapter (CH) SKIP CH 1 CH 2 CH 3 CH 4 SKIP +10 Within 30 seconds Using the SKIP H , G button 1 PLAY SKIP Current Track (TR) SKIP TR 1 TR 2 TR 3 TR 4 SKIP Note ¡Depending on the disc being played, this function can also be performed by directly entering the desired chapter number with the number buttons. Refer to the manual accompanying the disc. Marker Setup DVD-V CD This feature allows you to assign a specific point on a disc to be called back later. To set a marker 1 PLAY To return to the marker later 1 PLAY To e xit the marker screen 1 RETURN SEARCH MODE SEARCH MODE Press repeatedly until this screen appears Notes ¡Opening the disc tray or turning off the power will erase all markers. ¡Selecting "AC" at step [2] in the section "To set a marker" will also erase all markers. ¡To clear a marker, select the marker to be cleared at step [2] in the section "To return to the marker later, " and then press the CLEAR button. Press repeatedly until this screen appears 2 or 2 or 3 3 ENTER ENTER at the desired marker ·Playback will restart from the specific point which you set. ­ 11 ­ EN Functions Repeat / Random / Programmed Playback Repeat Playback DVD-V CD Repeat A-B Playback DVD-V CD Programmed Playback CD Repeat function is available only during playback. 1 PLAY You may determine the order in which tracks will play. A- 1 PLAY A-B 1 STOP CD-DA TOTAL 0:00:00 at your desired starting point (A). REPEAT 2 Each time the REPEAT button is pressed. . . DVD-V A-B MODE ENTER A-B Press once at your desired end point (B). 2 CD-DA TOTAL 0:08:00 CHAPTER (current chapter repeat) TITLE OFF CD ¡Point B should be in the same title or track as point A is. or 8 3:30 9 2:30 10 1:30 ALL CLEAR ENTER 2/2 8 3:30 (current title repeat) (repeat off) ¡To exit the sequence, press the A-B button. ¡To cancel Point A, press the CLEAR button. ¡This function does not work in the other repeat modes. ENTER Up to 99 tracks can be ordered. TRACK ALL OFF (current track repeat) (entire disc repeat) 3 PLAY Functions Random Playback (repeat off) This shuffles the playing order of tracks instead of playback in the sequence. CD Notes ¡Press the CLEAR button at step [2] to erase the most recently entered program. ¡To erase all tracks in the program at once, select "ALL CLEAR'' and press the ENTER button at step [2]. ¡While a program is being played back, the STOP button works as follows; Press the STOP button and the PLAY button next, so that the programmed playback restarts. (CD playback restarts from the current point. ) Press the STOP button twice and the PLAY button next, so that playback restarts from the first track in the original order. However, your programmed playback can be restarted when you follow the above steps. [. . . ] · Para llamar el menú de ajustes de DVD. · Para empezar la reproducción del disco. · Para activar o desactivar la unidad. · Para reproducir repetidamente una canción o disco. 3 or PLAY Seleccione el idioma deseado para las indicaciones en la pantalla PLAYER MENU ENGLISH FRANÇAIS ESPAÑOL POWER REPEAT ENTER RETURN SEARCH MODE 4 Para salir del menú SETUP SETUP · Para buscar una canción. [. . . ]