User manual SYMPHONIC SV211E

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] Press the PLAY button to return to playback. NOTES: · You can advance the picture one frame at a time by pressing the PAUSE button during the Still mode. · If it is left in the Pause mode for more than five minutes, the TV/DVD/VCR will automatically switch to the Stop mode. TRACKING ADJUSTMENT TV/VCR · · · Tracking adjustment will be set automatically (Digital Tracking function) when you start playback. However when playing pre-recorded tapes or tapes recorded on units other than your own, noise lines (black and white streaks) may appear on the playback picture. If this occurs, you can adjust the tracking control manually by pressing the CHANNEL button K or L until the streaks disappear. To return to the DTR function, stop the tape once and start playback again. You can reduce the noise lines by pressing the CHANNEL button K or L in slow mode, too. Tracking adjustment in Slow mode will not be set automatically. VERTICAL HOLD CONTROL TV/VCR In the Pause/Still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the CHANNEL button K or L. NOTE: If there are video noise lines on the screen, see Tracking Adjustment section. SLOW MOTION TV/VCR During pause, press the FWD button to reduce the playback speed. The TV/DVD/VCR mutes the sound during slow motion. Press the PLAY button to return to normal playback. - 26 - EN 1C29 SPECIAL PLAYBACK Make sure . . . Select "TIME SEARCH" mode - TV/VCR SETUP TIMER PROGRAMMING SETTING CLOCK CHANNEL SET UP USER'S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN B TIME SEARCH INDEX SEARCH 1 Stop a tape at your desired point Rewind or fast forward the tape to the beginning point at which you want to review. 2 3 Reset the counter to 0:00:00 Press the SETUP button on the remote control. Press the Arrow button K or L to point to "TIME SEARCH". Then, press the ENTER button. Press the C. RESET button repeatedly. Begin recording or playback 3 Enter your desired time TIME SEARCH 2 : 50 Press the RECORD or PLAY button. Press the STOP button when recording or playback is completed. 4 To activate "ZERO RETURN" mode - TV/VCR SETUP TIMER PROGRAMMING SETTING CLOCK CHANNEL SET UP USER'S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] B ZERO RETURN TIME SEARCH INDEX SEARCH Press the Arrow button K or L until your desired time appears. (Example: "2:50" stands for 2 hours 50 minutes) If you wish to cancel the Time Search at this point, press the SETUP button on the remote control. Press the SETUP button on the remote control. Press the Arrow button K or L to point to "ZERO RETURN". The counter will appear on the TV screen. The tape will automatically stop when the counter returns to 0:00:00. 4 Begin Time Search By pressing the Arrow button s or B, the TV/DVD/VCR will rewind or fast forward to the specified point. The time counts down as the searching progresses. When 0:00 is reached, the tape will start playback automatically. TIME SEARCH TV/VCR The Time Search function makes it possible to quickly advance the tape to your desired position simply by entering the exact amount of playback time you want to skip. NOTES: · Time Search can be set up to a maximum of 9 hours 50 minutes (9:50) by 10 minutes at a time. TO CANCEL THE TIME SEARCH at this point Press the STOP/EJECT button on the TV/DVD/VCR or the STOP button on the remote control. [. . . ] There are no user-serviceable parts inside. Turn off, unplug the power cord, and please call our help line at 1-800-242-7158, to locate an Authorized Service Center. IF THE LASER OPTICAL PICKUP UNIT IS DIRTY · If the player still does not perform properly when it is operated while referring to the relevant sections and to "TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit. DISC HANDLING · Use discs which have the following logos on them. (Optical audio digital discs. ) Recordable ReWritable · Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs. · To clean-off, use a soft cloth. · Do not use a hard cloth since this will mar the disc. [. . . ]