User manual T-FAL B-80 BEERTENDER

[. . . ] Couverture B80 oneway seb. qxd:Couverture B80 oneway seb. qxd 23/06/08 11:09 Page 1 USA: 1-800-395-8325 www. t-falusa. com CANADA : 1-800-418-3325 www. t-fal. ca 0828 074 B80 one way T-FAL US modif heineken . qxd:B80 one way SEB Uklta. qxd 25/06/08 15:10 Page 3 1 - Important safeguards 2 - General Information 3 - Product description 4 - Before use 5 - Using the BeerTender® 6 - Troubleshooting 7 - Disposal 8 - Consumer service 9 - Limited warranty 4 6 7 7 8 13 16 16 17 3 ENGLISH B80 one way T-FAL US modif heineken . qxd:B80 one way SEB Uklta. qxd 25/06/08 15:10 Page 4 ENGLISH 1 - IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons including the following : 1. To protect against fire, electric shock and injury to persons, do not place cord, plugs or appliance in water or other liquid. Close supervision is necessary when any appliance is used near children. Keep appliance out of reach of children. [. . . ] Insufficiently chilled DraughtKegs will produce too much foam. It is ideal to purchase the DraughtKeg pre-chilled or pre-chill over night before intended use. If the DraughtKeg needs additional chilling, there are 2 recommended options: a. Inside the BeerTender ­ Depending on the temperature of the DraughtKeg, it will take up to 18 hours to chill to the ideal serving temperature. In a refrigerator ­ Depending on the temperature of your refrigerator, it will take up to 12 hours to chill to the ideal serving temperature. Tip: We recommend that you always keep an extra DraughtKeg in your refrigerator to always have a chilled keg available. Preparing the BeerTender IMPORTANT: It is important that the BeerTender power switch is turned on before inserting the DraughtKeg. 9 ENGLISH B80 one way T-FAL US modif heineken . qxd:B80 one way SEB Uklta. qxd 25/06/08 15:10 Page 10 * * * * * * * * * After setting up the BeerTender® and before use, it is vital to clean the detachable pour spout ­ this is the only part of the appliance that will come into contact with the beer. Before inserting the DraughtKegTM into the BeerTender, simply snap the patented disposable draught beer tube (5 tubes included) onto the DraughtKeg. Open the BeerTender cover by pressing in the release panel on the top of the machine. Remove the tap spout cover by lifting it up. Position the draught beer tube as shown in drawing. Put the tap spout cover back into place. Set the drip tray and grate in place at the front of the appliance. Make sure the drip tray is properly fitted and positioned. ENGLISH 10 B80 one way T-FAL US modif heineken . qxd:B80 one way SEB Uklta. qxd 25/06/08 15:10 Page 11 WARNING!The drip tray must be positioned on a level surface and must not jut out from the surface it is resting on. Control Panel Your appliance features a display providing you with important and useful information. Two LEDs on the top of the lid provide important indications: Green (ON/OFF) LED on the left of the panel: when lit, it indicates that the appliance is operating. Green beer-temperature LED on the right side of the panel: when the DraughtKegTM has reached the ideal temperature the LED switches on and the appliance goes into "stand-by" cooling mode. ENGLISH Warning: never use your BeerTender® with ambient temperature above 86°F. Above that level, the ideal serving temperature can not be attained. Pouring a beer from the BeerTender * Before pouring a beer, rinse a clean glass in cold water which chills the glass and wets the inside to enable a perfectly smooth draught pour. Use of 8 oz glasses is recommended to maintain the ideal serving temperature. Draught and Drink * Be aware that the first glass you pour from every new DraughtKeg will contain mostly foam. [. . . ] Defective products may be returned by the original purchaser or any subsequent owner within the warranty period, postage pre-paid together with proof of purchase (register receipt) to an authorized T-fal return facility. If product is returned without proof of purchase it will be reviewed based on the manufacturing production week and year to determine warranty coverage. Defective products will be replaced at no charge including return postage if it falls within the warranty timeframe. The warranty does not apply to any unit that has been tampered with, nor to damages incurred through improper use and care, faulty packing or mishandling by any common carrier. [. . . ]