User manual TAG MCLAREN AUDIO 100X5R

[. . . ] It perfectly compliments our excellent AV32R audio-visual processor and DVD32R dvd player. Whether used for twochannel stereo or full five channel surround sound, we are convinced that, with the 100x5R, you will never be disappointed. 05 04 features features Thank you for purchasing the TAG McLaren Audio five-channel amplifier 100x5R. five channel amplifier 100x5R s The 100x5R is a powerful, hi-performance amplifier which delivers sound reproduction of outstanding clarity and purity for up to five channels. TAG McLaren Audio's expertise in amplifier design has led to a product which will satisfy the audiophile and movie lover. For many years it has been considered quite impossible to setup a home cinema system to the same high standards as an audiophile stereo set-up. However, with the advent of ultrahigh-resolution, high-performance DVD, we now can have `no06 compromise' home cinema with truly excellent sound and picture quality. In many homes the home cinema system has now replaced the two channel stereo set-up, requiring components to complement but also to compete with the best audiophile products. [. . . ] In turn connect the black (­) terminal of the loudspeaker to the black terminal on the 100x5R. The diagram opposite shows a standard loudspeaker arrangement 1. To bi-wire your speakers, attach 2 spade connectors to each loudspeaker terminal or preferably use a single run of higher quality loudspeaker cable instead. 16 17 set-up remote control audio-visual processor or preamplifier connection You will require an audio-visual processor (such as our theatre AV32R) or a preamplifier (such as our PA10, PA20R or PA32R) to provide the signals to drive the 100x5R. Use a good quality, screened phono-phono audio cable, such as the TAG McLaren Audio F3-10-ANA, to connect between the phono socket output on the processor/preamplifier and the phono socket input on the rear module panel of the 100x5R. Ensure that the correct processor/preamplifier output e. g. left front is connected to the 100x5R module which in turn is connected to the left front speaker. Continue in this manner until all of the channels are connected. When you have completed the set-up and have connected all cables between all components, ensure that the volume control on the av processor/preamplifier is set to minimum before switching on. The 100x5R is equipped with a sophisticated micro-controller to monitor and control the 100x5R. The performance of this processor, activated by a tiny remote control, allows for class leading ergonomics, for example the flexibility to not only mute all five channels simultaneously but for example have individual control over each power amplifier module. So if you play CDs in stereo you only need to switch on the left and right channels. For added convenience TAG McLaren Audio has integrated the main control functions for the av processor AV32R and the dvd player DVD32R. The complete audio-visual system can be started, stopped or muted from the tiny remote control of the 100x5R. remote control confirming operation Whenever the 100x5R receives valid infra red (IR) instructions from the remote control the 100x5R acknowledges by flashing the top LED on the right front panel, above the power button. switch on Press the power button in. The five channel status indicators will flash, as the amplifier channels power up sequentially to prevent excessively high current demand from the mains supply. When all five channels have been activated, you should see the five red LEDs softly illuminated, showing that all five channels have energised. Then the amplifier is ready to play source material through the system. Raise the volume level at your av processor or preamplifier slowly at first, until sound is replayed through the audio system. Sit back and enjoy! 100x5R mute The sound output of all five channels can be muted using the single `mute amp' button on the remote. This is a toggle action command - one press will mute and a second press will un-mute. When muted the 100x5R has only disconnected the loudspeakers. The amplifier is still running and the sound will be restored instantly when the `mute' button is pressed again. When the 100x5R is muted the bottom LED on the right front panel, above the power button, will illuminate. 19 18 remote control remote control unit / system standby The 100x5R is provided with a `standby' mode. This function will switch off the power supplies of the amplifier module. [. . . ] If your 100x5R is still under guarantee, please refer to the guarantee card which gives you details on how to claim against the guarantee. Please keep the original packaging and use it whenever your 100x5R is transported. cleaning In order to maintain the appearance of your 100x5R, you can clean it as follows: before cleaning always disconnect your 100x5R from the AC supply; any grease or dirt on the case may be removed with a soft, lint free cloth moistened slightly with a mild solution of warm water and detergent or washing up liquid. Do not use any solvents or abrasives; take great care not to get any liquid inside the case. If this happens, you should have your 100x5R serviced. 1 You cannot open the fuse drawer while the plug is in the socket 26 27 technical data technical data This section is for those of you who really want to know the `insides' of your 100x5R. [. . . ]