User manual TAG MCLAREN AUDIO 100X5R:10

[. . . ] Providing completely independent amplification for each channel prevents interaction between them, resulting in a cleaner signal and hence better clarity and stereo imaging. This is true whether dealing with two channels or five!The 120 Watt Monobloc module is a complete self-contained amplifier, including its own power transformer, bridge rectifier, energy storage capacitors and amplification stage, requiring only mains supply and control signals for operation. The Monobloc module uses its own aluminium heat sink for excellent heat dissipation, allowing each module to drive even more critical loudspeakers safely and totally independently of any of the other modules. 120 Watt Monobloc module As a result of the Monobloc amplifier module construction, its performance is independent of the number of channels being driven and therefore even during the loudest passages of your favourite movie, the sound stage remains stable, controlled and detailed. [. . . ] The previous paragraph described the three different modes available for the Stereo module. This paragraph covers the Monobloc module: The Monobloc module offers a single channel high power mode, in which the signal connected to INPUT 1 is amplified and made available through loudspeaker OUTPUTS A. The Monobloc module does not contain an INPUT switch, INPUT 2 or OUTPUT B connectors. OUTPUTS | 19 1A 1A 2B 1B 1 C power x2 1 2 INPUTS + ­ A + ­ C B + ­ 20 | power and loudspeaker connection power connection Check that the power button is out, so that the power is off when you plug the unit in(1). Do not connect the power cable until you have made all other connections. loudspeaker connection On the rear panel of the 100x5R:10 you will find up to ten pairs of loudspeaker terminals, designed to accept high quality 8 mm spade connectors. Connection to a Stereo module should be done as described in the section operating modes; connection to a Monobloc module as described on page 19. Only use high quality loudspeaker cables, such as our TAG McLaren F3-10-SPK, terminated with high quality 8 mm spade connectors. 1. The power button is a latching switch. One press will hold it in; the next will release it AV processor connection audio-visual processor or preamplifier connection You will require an audio-visual processor (such as our AV32R) or a preamplifier (such as our DPA32R) to provide the signals to drive the 100x5R:10. Use good quality, screened phono-phono audio cables, such as the TAG McLaren F3-10-ANA, to connect between the phono socket output on the processor / preamplifier and the phono socket input on the rear panel of the 100x5R:10. Details are given in the section operating modes and Monobloc module connections, on page 19. Ensure that the correct processor / preamplifier output e. g. left front is connected to the 100x5R:10 module which in turn is connected to the left front speaker. Continue in this manner until all of the channels are connected. When you have completed the set-up and have connected all cables between all components, ensure that the volume control on the AV processor / preamplifier is set to minimum before switching on. RISK OF ELECTRIC SHOCK DO NOT OPEN | 21 Recommended connections when using a 100x5R:10 with 7 channels Most seven channel versions of the 100x5R:10 will be built as shown on page 3, ie: Monobloc, Stereo, Monobloc, Stereo, Monobloc. It is recommended that you attach the speakers of a 7. 1 configuration as follows (looking at the rear panel of your 100x5R:10)(1): RIGHT FRONT SPEAKER SURROUND LEFT/RIGHT SPEAKERS CENTRE SPEAKER BACK LEFT/RIGHT SPEAKERS LEFT FRONT SPEAKER 1A 1A 2B 1B 1A 1A 2B 1B 1A 1A 2B 1B 1A 1A 2B 1B 1A 1A 2B 1B 1 C power x2 1 C power x2 1 C power x2 1 C power x2 1 C power x2 1 2 INPUTS 1 2 INPUTS 1 2 INPUTS 1 2 INPUTS 1 2 INPUTS + ­ A + + ­ ­ C + + ­ ­ C + + ­ ­ C + + ­ ­ C A A A A C + ­ OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS 1 B + ­ 2 B + ­ 3 B + ­ 4 B + ­ 5 B + ­ multi-channel amplifier 100x5R:10 s made in United Kingdom This way the five module status LED's will be associated as follows(1) 1. CENTRE SPEAKER LEFT FRONT SPEAKER RIGHT FRONT SPEAKER BACK LEFT/RIGHT SPEAKERS SURROUND LEFT/RIGHT SPEAKER This configuration will also allow the AV processor AV32R, if connected to the 100x5R:10 via TAGtronic bus, to deactivate modules not required, e. g. Backs in 5. 1 22 | power up and switch on After connecting your preamplifier / AV processor and your loudspeakers connect the power cable, supplied to the 100x5R:10(1). The five module(2) status indicators will flash as the amplifier modules power up sequentially to prevent excessively high current demand from the mains supply. When all five modules have been activated, you should see the five red LEDs softly illuminated, showing that all five modules have energised. Then the amplifier is ready to play source material through the system. Raise the volume level at your AV processor or preamplifier slowly at first, until sound is replayed through the audio system. 2. Check that the power button is out, so that power is off when you plug in Assuming you have five modules installed remote control class leading ergonomics The 100x5R:10 is equipped with a sophisticated microcontroller to monitor and control the 100x5R:10. The + + performance of this processor, activated -by a compact remote control, allows for + class-leading ergonomics, such as -the flexibility not only to mute the complete amplifier but also to have control over each power amplifier module. CDs in stereo, you only need to switch on the left and right channels. S TA N D B Y AV | 23 confirming remote reception Whenever the 100x5R:10 receives valid infra red (IR) instructions from the remote control it acknowledges the command by flashing the remote control active LED. 100x5R:10 mute The sound output of the complete amplifier can be muted using the single mute amp button on the remote control. [. . . ] grounding The 100x5R:10 is double-insulated and does not require a safety ground connection running in and warming up TAG McLaren equipment is designed to give optimum performance for many years. | 31 running in Just like a high quality car, the performance of your 100x5R:10 will improve during the first few hours of operation. After these few hours, the electronic components will have reached and settled down to near perfect specification. warming up Every time you switch on your 100x5R:10, its performance will improve as the components reach their optimum operating temperature. 32 | care and maintenance fuses There is a fuse in the power socket on the back of your 100x5R:10. To change the fuse, unplug the power cable and carefully pull out the fuse carrier drawer(1). The fuse carrier contains a spare fuse; this is the first one that you see when you open the carrier. [. . . ]