User manual TANDBERG REPLACE TAPE DRIVE IN T24 OR T48

[. . . ] INSTALLING A TAPE DRIVE IN This document explains how to install or replace a tape drive in the Tandberg StorageLibrary T24 or Tandberg StorageLibrary T48. Please read the entire section that you are using prior to beginning the procedure. PREPARING FOR INSTALLATION OR REPLACEMENT Note: If your library is installed in a rack, it is not necessary to remove the library from the rack to complete this procedure. It is also not necessary to disconnect the Ethernet cable from the back of the library. Obtain these items--a #2 Phillips screwdriver and a small flat-blade screwdriver. [. . . ] Bottom Serial connector Bottom Internal label Drive 1 15 OF 28 Do not use middle connector with full height tape drive Serial cable (C) (route under carrier) Power cable (D) (route over carrier) Figure 15 StorageLibrary T24--replacing existing tape drives: full height connectors StorageLibrary T24 Half Height tape drive serial and power cable connections-- Serial--Route the serial cable (C) over the tape drive carrier and under the power cable as shown here; connect as shown in Figure 2 (StorageLibrary T24 HH serial cable routing). Power--Route the power cable through the tape drive carriers as shown here; connect as shown in Figure 4 (StorageLibrary T24 HH power cable routing). Tape drive Half height Quantity Second tape drive Single tape drive Install in this opening. . . Top Bottom Serial connector Top Bottom Internal label Drive 2 Drive 1 Press the serial cable (C) down into the carrier to prevent catching it between the tape drive and the library. Power cable (D) (route under carrier and over serial cable) Serial cable (C) (route over carrier and under the power cable) Tape drive carrier Figure 16 StorageLibrary T24--replacing existing tape drives: half height connectors 16 OF 28 StorageLibrary T48 Full Height tape drive serial and power cable connections-- Serial--Route the serial cable (C) under the tape drive carrier as shown here; connect as shown in Figure 1 (StorageLibrary T48 FH serial cable routing). Power--Route the power cable through the tape drive carriers as shown here; connect as shown in Figure 7 (StorageLibrary T48 FH power cable routing). Power cable (D) Route power cable through tape drive carriers Serial cable (C) Serial cable (C) Figure 17 StorageLibrary T48--replacing existing tape drives: full height connectors Serial cable (C) connectors Serial cable (C) Route under carrier. 17 OF 28 StorageLibrary T48 Half Height tape drive serial and power cable connections-- Serial--Route the serial cable (C) over the tape drive carrier as shown here; connect as shown in Figure 6 (StorageLibrary T48 HH serial cable routing). Power--Route the power cable through the tape drive carriers as shown here; connect as shown in Figure 8 (StorageLibrary T48 HH power cable routing). Serial cable (C) (route over carrier) Tape drive carrier Press the serial cable (C) down into the Power cable (D) carrier to prevent catching it between (route through carriers) the tape drive and the library. Figure 18 StorageLibrary T48--replacing existing tape drives: half height connectors d. Slide the tape drive the remaining distance into the library. Use care not to damage the cables during this step. Attach the SCSI cover plate (S) and the tape drive cover plate (P) that came with your replacement kit. See "Reference Illustrations" on page 3. ! Important The library requires both the SCSI cover plates (S) and the tape drive cover plates (P) for ESD protection. Do not connect the SCSI cables until after you reconfigure the library. b. Reconfigure your library--You must reconfigure your library for your backup application to recognize the new tape drive. See page 25 for instructions. 18 OF 28 REPLACING A TAPE DRIVE (HALF HEIGHT TO FULL HEIGHT) To replace a half height tape drive with a full height tape drive, follow these steps. Power off the library (press the 0 on the back of the unit) b. Disconnect the power cord, the SCSI or Fibre Channel cable(s), and the terminator (if present) c. Set the plate and the screws aside. Tape drive cover plate (P) Back of library Screws Screws Power OFF (press the 0) Disconnect power cord Figure 19 Note: Tape drive cover plate (StorageLibrary T48 half height SCSI library) This figure shows the StorageLibrary T48 FC library with two half height tape drives installed. Remove the StorageLibrary T24 tape drive cover plate (SCSI and Fibre Channel) the same way. 2. Removing the cables, internal cooling plates, and tape drives-- a. Pull the tape drive a short distance out of the library and disconnect the serial cable (C). Repeat for all the tape drives that you are replacing. Disconnect the power cables (D) from all of the tape drives. Remove the screws (A) holding the tape drive cooling plate (B). 19 OF 28 d. [. . . ] If necessary, enter the operator panel password (see page 72). Press until the selection arrow ( Drive Drive ID Drive SCSI ID Drive Configuration Library SCSI Bridge ) points to Drive Configuration. Select 3. Drive Configuration 1: 2: 3: 4: HP LTO-2 HalfHigh HP LTO-2 HalfHigh no drive no drive Back Modify Note: OK The library lists "no drive" only if there is no room for more tape drives. For example, in the above screen, the StorageLibrary T48 library has two half height tape drives. [. . . ]